background image

3

General 

Information 

          

The Shelter EPA-Approved Furnace has been engineered to accommodate the heating requirements of the average sized home, even 

during winter’s coldest months, with a heat output range up to 140,000 BTUs.  It is constructed with high grade, heavy gauge steel and 

is continuously welded to assure the highest structural strength.  In addition, the firebox is lined with insulated stainless steel panels to 

ensure many years of energy efficient service. The design of the secondary combustion chamber increases fuel efficiency by creating a 

“secondary burn” of smoke and wood gases before they are vented up the chimney. The cast iron doors are custom fitted to provide an 

airtight seal, greatly extending the burn time and ensuring maximum efficiency in fuel consumption.  The heavy-gauge cast iron grate, 

designed for maximum heat transfer, allows for convenient ash removal and reduced maintenance.

For total comfort and convenience, a thermostatically controlled draft and circulation blower system is included.  These fully automatic 

components furnish rapid heat disbursement throughout your home, minimizing recovery time when the wall thermostat demands heat.

All of these features are standard, offering you the most efficient, durable and affordable indoor wood burning furnace.

Efficiency was determined using the higher heating value of the fuel per B415.1-10 testing requirements. Dry seasoned wood will develop 

greater BTU output. A well-insulated dwelling will always lead to better results and overall improved fuel usage efficiency.

Your Shelter Furnace is designed to be either a supplemental or central heating source for your home.  This wood burning furnace may 

be installed in parallel with a properly operating electric, gas or oil-fired central furnace, listed or certified in accordance with a nationally 

recognized safety standard, and within clearances specified on the nameplate.  When in a parallel installation the static pressure of the 

central furnace plenum may not exceed 0.15 water column inches and the maximum setting on central furnace limit switch is 182°F.  With 

the Shelter Furnace in an “Interconnection Arrangement” your furnace should be upstream of the central furnace.  The Shelter Furnace 

warm air supply should never be connected to return air for the central furnace.  A qualified installer should perform the installation.

This wood heater needs periodic inspection and repair for proper operation. It is against federal regulations to operate this wood heater in 

a manner inconsistent with operating instructions in this manual.

IMPORTANT:  FOR TECHNICAL SUPPORT OR CUSTOMER SERVICE 

ISSUES, DO NOT RETURN TO THE STORE (THE STORE DOES NOT HAVE 

REPLACEMENT PARTS), CALL 1-800-875-4788.
Forced Hot Air Circulation:

The plenum size of your Shelter Furnace must not be reduced to less than 100 square inches, and must provide a minimum of 18 inches 

between the top of your Shelter Furnace and the main trunk connection.  The plenum attached to the furnace must be constructed of 

metal.  The warm air supply duct system should be constructed of materials with a minimum temperature rating of 250° Fahrenheit.

Clearances:

Unit must be placed on a non-combustible floor.  This floor must extend at least 16 inches in front, 8 inches on either side of fuel loading 

and ash removal doors, underneath the chimney connector and must extend 2 inches on either side of the chimney connector.  The 

furnace must maintain the following clearances to combustibles:
 

•  Heat plenum = 2 inches

 

•  Chimney connector = 18 inches

 

•  Front = 48 inches

 

•  Rear = 12 inches

 

•  Sides = 6 inches

 

•  Main furnace = 12 inches

These are minimum clearances and should be strictly followed.  In the case of a power outage, a dangerous level of heat accumulation 

may develop.  Do not store fuel or other combustible materials within installation clearances.

Summary of Contents for SF2600





























Reviews: