background image

Page 17

Figure 3.   Motor and Gear Box (Continued)

Ref.

Key

Qty.

No.

Number

Description

Req’d

1

Motor

1

10 and 15 Ton Hoists:

Single Speed:  .75 HP – Without Brake

CBH-2300

208-230/460 Volts, 3 Phase, 60 Hertz

CBH-2301

575 Volts, 3 Phase, 60 Hertz

Single Speed:  .75 HP – With Brake

CBH-2302

208-230/460 Volts, 3 Phase, 60 Hertz

CBH-2303

575 Volts, 3 Phase, 60 Hertz

Two Speed:  .75/.37 HP – Without Brake

CBH-2304

208 Volts, 3 Phase, 60 Hertz

CBH-2305

230 Volts, 3 Phase, 60 Hertz

CBH-2306

460 Volts, 3 Phase, 60 Hertz

CBH-2307

575 Volts, 3 Phase, 60 Hertz

Two Speed:  .75/.37 HP – With Brake

CBH-2308

208 Volts, 3 Phase, 60 Hertz

CBH-2309

230 Volts, 3 Phase, 60 Hertz

CBH-2310

460 Volts, 3 Phase, 60 Hertz

CBH-2311

575 Volts, 3 Phase, 60 Hertz

20 and 25 Ton Hoists:

Single Speed:  1.5 HP – Without Brake

CBH-2312

208-230/460 Volts, 3 Phase, 60 Hertz

CBH-2313

575 Volts, 3 Phase, 60 Hertz

Single Speed:  1.5 HP – With Brake

CBH-2314

208-230/460 Volts, 3 Phase, 60 Hertz

CBH-2315

575 Volts, 3 Phase, 60 Hertz

Two Speed:  1.5/.5 HP – Without Brake

CBH-2316

208 Volts, 3 Phase, 60 Hertz

CBH-2317

230 Volts, 3 Phase, 60 Hertz

CBH-2318

460 Volts, 3 Phase, 60 Hertz

CBH-2319

575 Volts, 3 Phase, 60 Hertz

Two Speed:  1.5/.5 HP – With Brake

CBH-2320

208 Volts, 3 Phase, 60 Hertz

CBH-2321

230 Volts, 3 Phase, 60 Hertz

CBH-2322

460 Volts, 3 Phase, 60 Hertz

CBH-2323

575 Volts, 3 Phase, 60 Hertz

2

CBH-2324

Key – Motor (3/16 x 3/16 x 1-1/4)

1

3

CBH-2325

Lockwasher (3/8)

4

4

CBH-2326

Bolt – Hex Head (3/8 - 16 x 7/8)

4

5

CBH-2327

Gear Box

1

6

CBH-2328

Key – Brake (Optional - 3/16 x 3/16 x 3/4)

1

7

Brake – Optional

1

CBH-2329

208-230/460 Volts, 3 Phase, 60 Hertz

CBH-2330

575 Volts, 3 Phase, 60 Hertz

ORDERING INSTRUCTIONS: Furnish complete data from motor and gearhead nameplates with parts order.

Replacement parts cannot be provided without this information.

 

Summary of Contents for Series 700





















Reviews: