Sharp XL-3600 Service Manual Download Page 37 | Manualshive

Page: 37 / 52

background image

– 37 –

XL-3600

XL-3700/C

• Focus servo sawtooth wave failure.

Is +7.0V applied to the pins 21 and 22 (VCC) of IC803 ?

Is sawtooh wave output to the pin 33 (FOO) of IC801 ?

IC801 is faulty.

No

Yes

Yes

Is sawtooth wave obtained between pins 17 and 18 of IC803 ?

No

No

Check the PWB pattern
between pin 7 of IC803
and pin 66 (CD STB) of
IC701.

Is +5V applied to the pin 7
(MUTE) of IC803 ?

Check the PWB pattern between pin 33 (FOO) of IC801 and pins
19 and 20 of IC803. If OK. IC803 is faulty.

Check the PWB pattern between pin emitter of Q605 and IC803.

No

Is sawtooth wave obtained between pins 13 and 16 of
CNP801/CNW801 ? (as shown above)

Yes

Check the PWB pattern between CNP801/CNW801 and IC803.

No

CNP801/CNW801 connection failure or optical pickup failure.

Yes

• Spindle motor clv servo failure.

Is above wave obtained between pins 1 and 2 of IC803 ?

Is following wave output to the pin 41 (DMO) of IC801 when
the CD TEST MODE "STEP 3" is changed to " STEP 4" ?

No

Yes

Check the procedure in "HF ERROR".
If OK. IC801 is faulty.

Check the PWB pattern between pin 41 (DMO) of IC801 and pins
9 and 10 of IC803. If OK. IC803 is faulty.

No

Is above wave obtained between pins 9 and 12 of CNP801/
CNW801 ?

Yes

Check the PWB pattern between CNP801/CNW801 and IC803.

No

CNP801/CNW801 connection failure or optical pickup failure.

Yes

DMO

Yes

1.5~2.5sec

1.5~2.5sec

«
...
35
36
37
38
39
...
»

Summary of Contents for XL-3600





















































Reviews:

No comments

Related manuals for XL-3600

Brand: C&K systems Pages: 28

Brand: C&K systems Pages: 2

Brand: C&K systems Pages: 40

Brand: d&b audiotechnik Pages: 10

MagnaLatch ALERT

Brand: D&D Technologies Pages: 2

Brand: Harman Kardon Pages: 11

Brand: Harman Kardon Pages: 8

Brand: Harman Kardon Pages: 9

Brand: Harman Kardon Pages: 2

Brand: Harman Kardon Pages: 2

Brand: Harman Kardon Pages: 18

Brand: Harman Kardon Pages: 2

MaestroKitchen 100

Brand: Harman Kardon Pages: 36

Brand: Harman Kardon Pages: 32

Brand: jablotron Pages: 30

Brand: Harman Kardon Pages: 50

Brand: La Crosse Technology Pages: 2

Brand: Rafiki Protection Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands