Sharp VIEWCAM VL-WD650U, Service Manual

Page: 12 / 133

12
VL-WD650U
Fig. 5. Position adjustment
(tape does not exist)
Fig. 6. S reel base no-load torque
measurement method
A
Fig. 4. Check (tape exists)
Tension roller position (S guide standard)
0
±
0.3
Screw2
Screw1
CCW
CW
Apply screwlock
Tension roller position (S guide standard)
0.2~0.6mm (Standard)
Tension roller
S guide
Tension band holder 4
Screw 3
7-4. Back tension torque check and adjustment in record (playback) mode
AC adapter used, with cassette controller assembly
(1) Checking
Set the torque cassette (SD-1015), and make sure in the SP record mode that
the supply side torque is within the standard shown below (or in the playback
mode for the tape on which the signal has been SP-recorded).
<Standard>
(If torque ripple exists, read its center value.)
0.7
±
0.1mN·m
(2) Adjustment (Fig. 4)
If the value is out of standard range, adjust, using the screw 1 shown in Fig. 4.
1. Loosen the screw 2 slightly.
2. Adjust to turning the screw 1. When back tension is too high, turn the screw
1 counterclockwise (CCW).
When back tension is too low, turn the screw 1 clockwise (CW).
3. After adjustment fix the angle with the screw 2. (At this time take care so as
to prevent excessive tightening.) Apply Screw Lock to the screw 1.
<Caution>
Screw tightening torque: 0.04N·m
7-5. Checking and adjustment of tension roller position in
record (playback) mode
DC3V, without cassette controller assembly (Independent Mechanism)
(1) Checking
Before winding the 60-min tape make sure that the tension roller is in the same
position as S guide as shown in Fig. 4.
If not, take out the tape and adjust in the following procedure.
(2) Adjustment (Fig. 5)
1. Set the playback mode without loading the tape.
2. Loosen the screw 3 slightly (to such an extent that the tension band holder
4 can be moved).
3. If the tension roller is inside from the specified position, shift the tension
band holder 4 in the arrow
A
direction. If the tension roller is outside, shift
the tension band holder in the arrow B direction, and fix with the screw 3.
(Proper shift must be 0.2 to 0.6mm outside from the specified position.)
4. Check the position by the procedure described in item (1) Checking above.
5. If the position is not specified position, adjust again.
7-6. Checking of supply S reel base no-load torque
DC3V, without cassette controller assembly (Independent Mechanism)
(1) Remove the cassette controller assembly, then apply DC3V to the loading
motor and put the system into L. start mode (refer to 9-1).
(2) Move the swing arm toward the Tu reel base side.
Be careful not to cause damage to the gears and other parts in the process. (Fig.
6)
(3) Set a back tension measurement reel hub on the S reel base.
(4) Using a dial tension gauge, pull the string in the A direction, then confirm that the
tension is within the standard.
<FF back tension standard>
(If the tension fluctuates, read its center value.)
30mN or less
7-7. Checking of loading back tension
DC3V, without cassette controller assembly (Independent Mechanism)
(1) Remove the cassette controller assembly, then apply DC3V to the loading
motor and put the system into L. start mode.
(refer to 9-1)
(2) Move the swing arm toward the S reel base side. Be careful not to cause
damage to the gears and other parts in the process. (Fig. 7)
(3) Set a back tension measurement reel hub on the Tu reel base.
(4) Using a dial tension gauge, pull the string in the A direction, then confirm that
the tension is within the standard.
Move the swing arm
toward the Tu reel
base side.