manualshive.com logo in svg

Sharp VC-S2000GM, Manual, Page: 45 / 47

Share
Download
Sharp VC-S2000GM Manual Download Page 45

 

GB-45

 

TROUBLESHOOTING

 

TROUBLESHOOTING

 

AREA

PROBLEM

POSSIBLE CAUSE/CURE

 

INITIAL 

INSTALLATION

 

When the VCR is first 
plugged in the VCR 
display appears blank. 
When the 

 

STANDBY

 

 

(

) 

button is pressed the 
display still appears 
blank.

• The Video may be in POWERSAVE mode. Press 

the 

 

STOP

 

 (

) button to switch the VCR on 

then press and hold the 

 

MENU

 

 and 

 

CHANNEL 

 

 buttons together on the front of the VCR for 

10 seconds. 
Now continue from step 1 of TUNING THE TV INTO 
THE VCR.

 

INSTALLATION

 

TV will not tune in to 
the VCR. 

• Check all the cables are correctly connected.
• Check your TV manual for correct tuning of your 

TV.

Auto Installation 
screen does not 
appear when the VCR 
is switched on OR Auto 
Installation is not 
complete.

• Reset the VCR and complete AUTO 

INSTALLATION again. (Refer to VCR Reset at the 
back of the book.)

 

POWER

 

Display is not working.

• Make sure the VCR is not in POWERSAVE mode.
• Make sure the power cord is plugged in.
• Make sure the wall socket has power (plug 

another appliance in).

VCR will not operate - 

 appears in VCR 

display.

• Press the 

 

TIMER ON/OFF

 

 button to disengage 

timer.

VCR will not respond 
to any commands.

• Check CHILD LOCK is not engaged.
• Safety device operating: unplug VCR for 2 

hours.

 

PLAYBACK

 

No picture appears.

• Make sure the TV is set to the video channel.
• Check all connecting cables.

Playback picture is 
snowy.

• Adjust the tracking using 

 

CHANNEL

 

 /

 buttons.

• Try another tape.
• The video heads may have been 

contaminated - refer to a SHARP Service Facility. 

 

RECORDING

 

Tape is automatically 
ejected when pressing 

 

REC

 

 (

) or 

 

TIMER

ON/OFF

 

 buttons.

• The record-protection tab has been removed.

Playback/ recording 
does not playback in 
stereo.

• Ensure VCR is connected to a stereo TV and 

SCART lead.

• Programme may not carry stereo.

SHOWVIEW does not 
record desired 
programme.

• Broadcast does not carry VPS/PDC signal which 

alters recording time.

• Check VPS/PDC mode is switched to ON.
• Ensure date and time are correctly set on the 

VCR.

 

TAPE 

TRANSPORT/

MECHANISM

 

Tape can not be 
loaded.

• Make sure there is no other tape in the VCR.
• Make sure you are loading the tape correctly.

Rewind is not possible. • Make sure the tape is not at the start.

 

Module 22F.fm  Page 45  Thursday, September 14, 2000  4:24 PM

Summary of Contents for VC-S2000GM
















































Reviews:

No comments