R-8000G
35
1. Disconnect the power supply cord.
2. Remove the outer case cabinet, referring to “OUTER CASE
CABINET REMOVAL”.
3. Open the oven door and block it open.
4. Discharge the high voltage capacitor.
5. Remove the back plate from the oven, referring to “BACK
PLATE REMOVAL”.
6. Remove the heater duct left assembly from the oven cavity,
SIDE HEATING ELEMENT REMOVAL
referring to "EXHAUST DUCT, HEATER DUCT LEFT
ASSEMBLY, CONVECTION DUCT ASSEMBLY AND HEATER
DUCT UPPER ASSEMBLY REMOVAL".
7. Remove the one (1) screw holding the heater mounting angle
B to the heater duct left.
8. Remove the two (2) nuts holding the side heating element to
the heater duct left.
9. Now, the side heating element is free.
1. Disconnect the power supply cord.
2. Remove the outer case cabinet, referring to “OUTER CASE
CABINET REMOVAL”.
3. Open the oven door and block it open.
4. Discharge the high voltage capacitor.
5. Remove the back plate from the oven, referring to “BACK
PLATE REMOVAL”.
6. Remove the convection duct assembly from the oven cavity,
referring to "EXHAUST DUCT, HEATER DUCT LEFT
ASSEMBLY, CONVECTION DUCT ASSEMBLY AND HEATER
DUCT UPPER ASSEMBLY REMOVAL".
JET MOTOR REMOVAL
7. Loosen the one (1) screw holding the convection fan assembly
to the jet motor shaft with a hexagon key wrench, and remove
the convection fan.
8. Remove the four (4) screws holding the convection motor
mounting angle to the convection duct.
9. Remove the six (6) screws holding the jet motor to the convection
motor mounting angle.
10. Remove the jet motor from the convection motor mounting
angle.
11. Now, the jet motor is free.
1. Disconnect the power supply cord.
2. Remove the outer case cabinet, referring to “OUTER CASE
CABINET REMOVAL”.
3. Open the oven door and block it open.
4. Discharge the high voltage capacitor.
5. Remove the back plate from the oven, referring to “BACK
PLATE REMOVAL”.
6. Remove the heater duct left assembly from the oven cavity,
TOP HEATING ELEMENT REMOVAL
referring to "EXHAUST DUCT, HEATER DUCT LEFT
ASSEMBLY, CONVECTION DUCT ASSEMBLY AND HEATER
DUCT UPPER ASSEMBLY REMOVAL".
7. Remove the one (1) screw holding the heater mounting angle
A to the heater duct upper.
8. Remove the two (2) nuts and the two (2) screws holding the top
heating element to the heater duct upper.
9. Now, the top heating element is free.
1. Disconnect the power supply cord.
2. Wait for 60 seconds to discharge the high voltage capacitor.
3. Remove the turntable tray and the turntable support from the
oven cavity.
4. Lay the oven on its backside.
5. Remove the turntable motor cover by snipping off the material
in four corners.
6. Where the corners have been snipped off, bend corner areas
TURNTABLE MOTOR REMOVAL
flat. No sharp edges must be evident after removal of the
turntable motor.
7. Disconnect the wire leads from the turntable motor.
8. Remove the one (1) screw holding the turntable motor to the
oven cavity bottom plate.
9. Now, the turntable motor is free.
10. After replacement, use the one (1) screw to fit the turntable
motor cover.
Removal
1. Disconnect the power supply cord.
2. Remove the outer case cabinet, referring to “OUTER CASE
CABINET REMOVAL”.
3. Open the oven door and block it open.
4. Discharge the high voltage capacitor.
5. Disconnect the wire leads from the switch.
6. Remove the one (1) screw holding the latch hook (right or left)
to the oven cavity front plate, and release the latch hook (right
or left).
7. Keep pushing the stopper tab holding the switch to the latch
hook (right or left) and revolve the switch on the pole.
8. Remove the switch from the latch hook (right or left).
9. Now, the switch is free.
DOOR SENSING SWITCH, SECONDARY INTERLOCK SWITCH, 3RD LATCH SWITCH AND
MONITOR SWITCH REPLACEMENT
Figure C-5. Switches
Door
sensing switch
Latch hook right
Monitor
switch
3rd. latch
switch
Latch hook left
Secondary
interlock
switch
Pole
Pole
Pole
Pole
Stopper
tab
Stopper
tab
Stopper
tab
Stopper
tab