background image

21

R-510EK
R-510EW

1. Precautions for Handling Electronic Components

This unit uses CMOS LSI in the integral part of the
circuits. When handling these parts, the following
precautions should be strictly followed. CMOS LSI have
extremely high impedance at its input and output
terminals. For this reason, it is easily influenced by the
surrounding high voltage power source, static electricity
charge in clothes, etc. and sometimes it is not fully
protected by the built-in protection circuit.
In order to protect CMOS LSI.

1) When storing and transporting, thoroughly wrap them in

aluminium foil. Also wrap all PW boards containing them
in aluminium foil.

2) When soldering, ground the technician as shown in the

figure and use grounded soldering iron and work table.

TOUCH CONTROL PANEL SERVICING

repair all the controls (sensor-related ones included) of
the touch control panel while keeping it connected to the
oven.

B. On some models, the power supply cord between the

touch control panel and the oven proper is long enough
that they may be separated from each other. For those
models, it is possible to check and repair the controls of
the touch control panel while keeping it apart from the
oven proper; in this case you must short both ends of the
door sensing switch (on PWB) of the touch control panel
with a jumper, which activates an operational state that
is equivalent to the oven door being closed. As for the
sensor-related controls of the touch control panel,
checking them is possible if dummy resistor(s) with
resistance equal to that of the controls are used.

(2) Servicing the touch control panel with power supply

from an external power source:
Disconnect the touch control panel completely from the
oven proper, and short both ends of the door sensing
switch (on PWB) of the touch control panel, which
activates an operational state that is equivalent to the
oven door being closed. Connect an external power
source to the power input terminal of the touch control
panel, then it is possible to check and repair the controls
of the touch control panel it is also possible to check the
sensor-related controls of the touch control panel by
using the dummy resistor(s).

3. Servicing Tools

Tools required to service the touch control panel
assembly.

1) Soldering iron: 30W

(It is recommended to use a soldering iron with a grounding
terminal.)

2) Oscilloscope: Single beam, frequency range: DC-10MHz

type or more advanced model.

3) Others: Hand tools

4. Other Precautions
1) Before turning on the power source of the control unit,

remove the aluminium foil applied for preventing static
electricity.

2) Connect the connectors of the key unit to the control unit

being sure that the lead wires are not twisted.

3) After aluminium foil is removed, be careful that abnormal

voltage due to static electricity etc. is not applied to the
input or output terminals.

4) Attach connectors, electrolytic capacitors, etc. to PWB,

making sure that all connections are tight.

5) Be sure to use specified components where high precision

is required.

2. Servicing of Touch Control Panel

We describe the procedures to permit servicing of the
touch control panel of the microwave oven and the
precautions you must take when doing so. To perform
the servicing, power to the touch control panel is available
either from the power line of the oven itself or from an
external power source.

(1) Servicing the touch control panel with power supply

of the oven:
CAUTION:
THE HIGH VOLTAGE TRANSFORMER OF THE
MICROWAVE OVEN IS STILL LIVE DURING
SERVICING AND  PRESENTS A HAZARD.
Therefore, before checking the performance of the touch
control panel,
1) Disconnect the power supply cord, and then remove

outer case.

2) Open the door and block it open.
3) Discharge high voltage capacitor.
4) Disconnect the leads to the primary of the power

transformer.

5) Ensure that these leads remain isolated from other

components and oven chassis by using insulation
tape.

6) After that procedure, re-connect the power supply

cord.

After checking the performance of the touch control panel,

1) Disconnect the power supply cord.
2) Open the door and block it open.
3) Re-connect the leads to the primary of the power

transformer.

4) Re-install the outer case (cabinet).
5) Re-connect the power supply cord after the outer

case is installed.

6) Run the oven and check all functions.

A. On some models, the power supply cord between the

touch control panel and the oven itself is so short that the
two can’t be separated. For those models, check and

approx. 1M ohm

Summary of Contents for R-510EK









































Reviews: