Sharp MD-MT80W(S) Service Manual Download Page 9

Page: 9 / 56

– 9 –

MD-MT80W/90W/90/90C

MD-MT90/90C

■

Checking the remaining amount of bat-
tery level

The remaining amount of battery level is shown by the
battery indicator (

) during operation.

●

When the battery is completely discharged, the bat-
tery indicator will flash. Recharge the battery or
replace the alkaline battery with a new one.

●

When the battery has run completely out, "BATT
EMPTY" will appear. Then, the power will be discon-
nected automatically.

Notes:

●

If you use the battery which you stopped charging
halfway, "

" may appear. It does not mean that the

battery is completely charged.

●

The battery indicator will not correctly display the
remaining capacity for approximately 10 seconds after
the power has been turned on.

●

When the AC adaptor or a separately available car
adaptor is used, the battery indicator will not be
shown.

●

The number of bars shown in the battery indicator may
increase or decrease, depending on the operation
being performed. This is normal.

■

Using with the rechargeable or alkaline
battery

Notes:

●

Setting the volume level to "0" whilst recording with the
rechargeable or an alkaline battery reduces the bat-
tery drain.

●

When you do not use the unit for hours, remove the
battery. (The battery drains gradually even when the
power is turned off.)

●

This unit can be used with the AC adaptor when the

●

Carry the battery in the supplied case.

(Except for MD-MT80W)

rechargeable or an alkaline battery is in the unit.

Caution:
Do not use a nickel-cadmium battery.

Disconnect the AC adaptor.

Insert the rechargeable bat-
tery or alkaline battery from
the (+) marked side.

Use a commercially available LR6,
"AA" size alkaline battery.

Battery Power

■

Charging the rechargeable battery

When the rechargeable battery is used for the first time
or when you want to use it after a long period of disuse,
be sure to charge it fully.

●

After the rechargeable battery is charged or used, it
will get slightly warm. This is normal.

●

When the portable MD is turned on or operating, the
battery will not be charged.

Insert the rechargeable battery.

A rechargeable battery other than the one supplied
or the optional one (AD-N70BT) cannot be charged.

Plug the AC adaptor into the AC outlet, and
then insert the plug on the other end into
the DC IN 5V jack.

Press the MODE/CHRG button.

" will flash, and battery will begin charging.

MD-MT80W/90W/90/90C

Summary of Contents for MD-MT80W(S)

























































Search results

Summary of Contents for MD-MT80W(S)

Reviews:

Related manuals for MD-MT80W(S)

Brands by name

Popular brands

Sharp MD-MT80W(S), Service Manual

Search results

Summary of Contents for MD-MT80W(S)

Reviews:

Related manuals for MD-MT80W(S)

Brands by name

Popular brands