Sharp MD-MS200H Service Manual Download Page 3

Page: 3 / 56

MD-MS200W/MD-MS200/MD-MS200H

– 3 –

BATTERY DISPOSAL (FOR MD-MS200 ONLY)

Contains nickel cadmium (or sealed lead) battery. Must be recycled
or disposed of properly. Remove the battery from the product and
contact federal or state environmental agencies for information on

recycling and disposal options.

FOR A COMPLETE DESCRIPTION OF THE OPERATION OF THIS UNIT, PLEASE REFER
TO THE OPERATION MANUAL.

SPECIFICATIONS

General

Power source:

DC 3.6 V (rechargeable lithium-ion
battery x 1)
DC 5 V (AC adaptor)
AC 110 - 240V, 50/60 Hz

Power consumption:

0.15 A (AC adaptor)
4 W

Output power:

RMS; 20mW (10 mW + 10mW)
(0.2% T.H.D.)

Rechargeable battery

Approx. 9.5 hours (continuous play)

performance:

Approx. 7.0 hours (continuous

(Fully charged)

recording)

Input sensitivity:

Output level:

Dimensions:

Width: 4-5/16" (109.2 mm)
Height: 1-7/32" (30.5 mm)
Depth: 3-7/32" (81.3 mm)

Weight:

275 g (0.6 lbs.) with rechargeable
battery

Input jack:

Line/Mic/Optical

Output jack:

Headphones

MiniDisc Recorder

Type:

Portable MiniDisc recorder

Signal readout:

Non-contact, semi-coductor laser
pick-up

Audio channels:

Frequency response:

20 to 20,000 Hz

3 dB

Rotation speed:

Approximately 400 to 900 rpm

Error correction:

ACIRC (Advanced Cross Interleave
Reed-Solomon Code)

Coding:

ATRAC (Adaptive TRansform
Acoustic Coding)

Recording method:

Magnetic modulation overwrite
method

A/D,D/A converter:

1-bit

Sampling frequency:

44.1 kHz

Modulation system:

EFM (Eight to Fourteen Modulation)

Wow and flutter:

Unmeasurable (less than

0.001%

W.peek)

Headphones

Type:

Inner-ear dynamic

Impedance:

16 ohms

Recording

level

Reference input

level

Input

inpedance

MIC H

0.25 mV

10k ohms

MIC L

2.5 mV

10k ohms

LINE

100 mV

20k ohms

Load

impedance

Headphones

—

10 mW +

16 ohms

10 mW

LINE

350mV

—

50 kohms

(-12dB)

Maximum

output level

Specified

output

Specifications for this model are subject to change without
prior notice.

Summary of Contents for MD-MS200H

























































Search results

Summary of Contents for MD-MS200H

Reviews:

Related manuals for MD-MS200H

Brands by name

Popular brands

Sharp MD-MS200H, Service Manual

Search results

Summary of Contents for MD-MS200H

Reviews:

Related manuals for MD-MS200H

Brands by name

Popular brands