Sharp LC52SB55U - LC - 52" LCD TV Service Manual Download Page 22

Page: 22 / 112

LC-52SB55U

5 – 4

2.4. Upgrading LCD controller software

Create the USB memory for LCD controller software version upgrade in the same manner as explained in the “Main software version upgrade”.

Copy the file LAKELAxx.USB and LAKELDxx.LCD to USB memory.

2.4.1 How to upgrade the software

1. Unplug the AC cord.

2. Insert the USB Memory for version upgrade (prepared as above) into the service socket located Right side of Main Board terminals, under INPUT3

terminal.

3. Plug in the AC cord with power button pressed down after 5 seconds, unpress the power button.

4. After the unit startup, the system upgrade screen as shown below appears within 20-40 seconds.

5. Even a single failure in the process will trigger the upgrade failure screen.

6. Upon completion of the whole process, the upgrade success screen as shown below appears. You can check the new software version on this

screen. The version information appears after the upgrade is complete.

7. Unplug the AC cord and remove the USB Memory for version upgrade.

8. Now the software version upgrade is complete.

SB55

UPGRADE FAILURE

SB55

UPGRADE SUCCESS

SB55

Summary of Contents for LC52SB55U - LC - 52" LCD TV

















































































































Search results

Summary of Contents for LC52SB55U - LC - 52" LCD TV

Reviews:

Related manuals for LC52SB55U - LC - 52" LCD TV

Brands by name

Popular brands

Sharp LC52SB55U - LC - 52" LCD TV, Service Manual

Search results

Summary of Contents for LC52SB55U - LC - 52" LCD TV

Reviews:

Related manuals for LC52SB55U - LC - 52" LCD TV

Brands by name

Popular brands