ELECTRICAL ADJUSTMENTS
D-1
1. ADJUSTMENT PROCEDURE
Read and perform these adjustments when repairing the
circuits or replacing electrical parts or PCB assemblies.
CAUTION
On-Screen Display Adjustment
1.
2.
Set the VOLUME to minimum.
Press the VOL. DOWN button on the set and the
channel button (9) on the remote control for more than
2 seconds to display adjustment mode on the screen
as shown in Fig. 1-1.
Fig. 1-1
3.
4.
5.
6.
7.
8.
9.
Use the CH. UP/DOWN button or Channel button (0-9)
on the remote control to select the options shown in Fig.
1-2.
Press the SETUP/TV MENU button on the remote control
to end the adjustments.
To display the adjustment screen for TV, AV,
COMPONENT, HDMI and PC mode, press the INPUT
SELECT button on the remote control.
To display the adjustment screen for DVD mode, press
the TV/DVD button on the remote control.
Receive the DIGITAL broadcasting.
To display the adjustment screen for DTV mode, select
the digital channel.
Press the VOL.DOWN button on the set and the channel
(9) on the remote control for more than 2 seconds.
•
•
•
Use an isolation transformer when performing any
service on this chassis.
When removing a PCB or related component, after
unfastening or changing a wire, be sure to put the wire
back in its original position.
When you exchange IC and Transistor with a heat sink,
apply silicon grease (YG6260M) on the contact section
of the heat sink. Before applying new silicon grease,
remove all the old silicon grease. (Old grease may
cause damages to the IC and Transistor).
2. BASIC ADJUSTMENTS
Prepare the following measurement tools for electrical
adjustments.
1. Pattern Generator
03 R DRIVE (N)
2
TV
FULL
480i
Function
Step No.
2-1: WHITE BALANCE
1.
2.
3.
4.
5.
6.
7.
8.
Place the set in Aging Test for more than 15 minutes.
Receive the gray scale pattern from the Pattern
Generator.
Press the INPUT SELECT button on the remote control
to set to the AV mode.
Using the remote control, set the brightness and
contrast to normal position.
Activate the adjustment mode display of Fig. 1-2 and
press the channel button (03) on the remote control to
select "R DRIVE(N)".
Press the CH. UP/DOWN button on the remote control
to select the "R DRIVE (N)", "R CUT OFF (N)",
"B DRIVE (N)", "B CUT OFF (N)", "R DRIVE (C)",
"R CUT OFF (C)", "B DRIVE (C)", "B CUT OFF (C)",
"R DRIVE (W)","R CUT OFF (W), "B DRIVE (W)" or
"B CUTOFF(W)".
Adjust the LEFT/RIGHT button on the remote control
to whiten the R DRIVE (N), R CUT OFF (N),
B DRIVE (N), B CUT OFF (N), R DRIVE (C),
R CUT OFF (C), B DRIVE (C), B CUT OFF (C),
R DRIVE (W) ,R CUT OFF (W), B DRIVE (W) and
B CUTOFF(W) at each step tone sections equally.
Perform the above adjustments 6 and 7 until the white
color is achieved.
FUNCTION
R DRIVE(N)
R CUT OFF(N)
G DRIVE(N)
G CUT OFF(N)
B DRIVE(N)
B CUT OFF(N)
R DRIVE(C)
R CUT OFF(C)
G DRIVE(C)
G CUT OFF(C)
B DRIVE(C)
B CUT OFF(C)
R DRIVE(W)
R CUT OFF(W)
G DRIVE(W)
G CUT OFF(W)
B DRIVE(W)
B CUT OFF(W)
BAK LIGHT CENT
BAK LIGHT MAX
NO.
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
29
30
NO.
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
50
FUNCTION
BAK LIGHT MIN
BRIGHTNESS CENT
BRIGHTNESS MAX
BRIGHTNESS MIN
TINT
SHARP H1 MAX
SHARP H1 MIN
SHARP H2 MAX
SHARP H2 MIN
SHARP V1 MAX
SHARP V1 MIN
CONTRAST CENTER
CONTRAST MAX
CONTRAST MIN
COLOR CENTER
COLOR MAX
COLOR MIN
CONTRAST 40
Fig. 1-2
