![background image](http://html.mh-extra.com/html/sharp/lc-26dv24u/lc-26dv24u_service-manual_373857016.webp)
DISASSEMBLY INSTRUCTIONS
B1-1
1. REMOVAL OF MECHANICAL PARTS
AND P.C. BOARDS
1-1: BACK CABINET (Refer to Fig. 1-1)
1.
2.
3.
Remove the 14 screws (1).
Remove the 7 screws (2).
Remove the Back Cabinet in the direction of arrow.
Fig. 1-2
Pick Up PCB
DVD MT PCB
1.
2.
3.
4.
5.
6.
7.
8.
Disconnect the following connector:
(CP6202).
Remove the Plate Button Ass'y in the direction of
arrow (A).
Remove the 6 screws (1).
Remove the Operation PCB and Operation 2 PCB in
the direction of arrow (B).
Remove the 2 screws (2).
Remove the 7 screws (3).
Remove the Angle Hinge in the direction of arrow (C).
(1)
(1)
DVD Deck
(A)
(2)
Angle MPEG
(5)
(5)
Short circuit using
a soldering iron.
Fig. 1-1
Back Cabinet
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(2)
(2)
(2)
(2)
(2)
(2)
1-2: DVD MT PCB/DVD DECK (Refer to Fig. 1-2)
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
Short circuit the position shown in Fig. 1-2 using a
soldering iron. If you remove the DVD Deck with no
soldering, the Laser may be damaged.
Disconnect the following connectors:
(CP403 and CP4301).
Remove the 2 screws (1).
Remove the 2 screws (2).
Remove the DVD Deck in the direction of arrow (A).
Remove the 2 screws (3).
Remove the Angle MPEG in the direction of
arrow (B).
Disconnect the following connectors:
(CP2301, CP2302 and CP2303).
Remove the 4 screws (4).
Remove the DVD MT PCB in the direction of arrow (C).
Remove the 2 screws (5).
Remove the Angle DVD-1 in the direction of arrow (D).
Fig. 1-3
Operation PCB
(1)
Plate Button Ass'y
(B)
(A)
(1)
(1)
(1)
(2)
(3)
(3)
(3)
Operation 2 PCB
(1)
(C)
(3)
Angle Hinge
(2)
(3)
(3)
(B)
(C)
(4)
(4) (4)
(4)
(D)
Angle DVD-1
(1)
NOTE
Before your operation, please read "PREPARATION
OF SERVICING".
Use the Lead Free solder.
Manual soldering conditions
ï Soldering temperature: 320
±
20
∞
C
ï Soldering time: Within 3 seconds
ï Soldering combination: Sn-3.0Ag-0.5Cu
When Soldering/Removing of solder, use the drawing
equipment over the Pick Up Unit to keep the Flux
smoke away from it.
When installing the DVD Deck, remove all the soldering
on the short circuit position after the connection of Pick
Up PCB and DVD MT PCB connector.
1.
2.
3.
4.
5.
OPERATION PCB/OPERATION2 PCB and
STAND ASS'Y (Refer to Fig. 1-3)
1-3:
(1)
(1)
(1)
(1)
(1)
(2)
(3)
(3)