manualshive.com logo in svg

Sharp Insight-Pro KB-4425L, Installation Manual, Page: 8 / 8

Share
Download
Sharp Insight-Pro KB-4425L Installation Manual Download Page 8

8

INSTALLATION MANUAL

 MODEL AND SERIAL NUMBER LOCATION

The name plate, including model and serial number, is located on 

the faceplate behind the Microwave Drawer front.

 CARE, CLEANING AND MAINTENANCE

Refer to the Operation Manual for cleaning instructions. If removing 

the range is necessary for cleaning or maintenance, disconnect the 

electrical power supply. If the electrical supply is inaccessible, lift 

the unit slightly at the front and pull out away from the wall. Pull 

only as far as necessary to disconnect the electrical supply. Finish 

removing the unit for servicing and cleaning. Reinstall in reverse 

order making sure to level the range and check electrical connections. 

See pages 2 and 3 for proper anchoring instructions.

PRINTED IN USA

TINSEB407MRR0

SHARP ELECTRONICS CORPORATION

Sharp Plaza, Mahwah, New Jersey 07430-2135

 BEFORE YOU CALL FOR SERVICE

Read the BEFORE YOU CALL and operating instruction sections 

in your Operation Manual. It may save you time and expense. The 

list includes common occurrences that are not the result of defective 

workmanship or materials in this range. 
Refer to the warranty in your Operation Manual for our toll-free 

service number and address. Please call or write if you have inquiries 

about your range product and/or need to order parts.

NOTE

 

Please do not open or close the lower oven door for 30 

seconds after plugged in.

Summary of Contents for Insight-Pro KB-4425L









Reviews:

No comments