The following steps should only be performed if there is a
power failure or if this unit is unplugged for more than 1 hour.
Turn on the TV and select the video channel on the TV.
Press
OPERATE
, then
VCR
.
Press
K
or
L
repeatedly to select your desired language.
Press
MENU
.
4
3
2
1
Turning on Your VCR/DVD
Press
VCR
, then
MENU
.
Press
K
or
L
to select INITIAL, then press
B
.
Press
K
or
L
to select LANGUAGE, then press
B
.
Press
K
or
L
repeatedly to select your desired language,
and
MENU
to confirm.
4
3
2
1
Changing the Language
– 12 –
EN
SETTING UP YOUR VCR/DVD COMBINATION
Playing Dolby Digital (5.1 channel), DTS or MPEG audio
Connecting an amplifier with a Dolby Digital/ DTS/ MPEG Audio digital surround processor to your VCR/DVD’s coaxial digital
jack provides richer and more powerful audio play.
C
C
Digital connection to a processor or amplifier with a coaxial digital input jack
You can make this connection using a coaxial digital cable.
NOTES:
• This connection is not possible if the processor or amplifier to which you want to connect does not have a coaxial digital
input jack.
• ANALOG AUDIO OUT and AV (TV) of the VCR/DVD are not available on the DTS audio.
DIGITAL IN
COAXIAL
To coaxial digital
input jack
Coaxial digital cable
(commercially available)
Dolby Digital (5.1 ch) /
DTS / MPEG Audio
processor or amplifier
DVD
DIGITAL
AUDIO OUT
ANALOG
AUDIO OUT
S-VIDEO
OUT
COAXIAL
L
R
VCR
AV2 (DECODER)
AV1 (TV)
DVD/VCR
A E R I A L
R F O U T
To COAXIAL
DIGITAL AUDIO
OUT jack
VCR/DVD SET UP
Video Channel setting will be necessary, if your VCR/DVD is
connected to the TV via the round coaxial cable.
Press
VCR.
Insert a pre-recorded tape into the cassette compart-
ment.
Playback will start automatically.
If playback does not start, press
PLAY
.
Select and adjust your TV to channel 36.
• If the playback picture appears on the TV screen, con-
tinue with step
.
• If channel 36 is set for broadcasting, or interference
lines appear on the picture, the RF converter must be
set to a different channel between CH22 and CH69.
Continue with step
.
4
9
3
2
1
Video Channel Setting
Press
MENU
.
Press
K
or
L
repeatedly to select INITIAL, then press
B
.
Press
K
or
L
repeatedly to select RF OUT, then press
B
.
The RF OUT CH menu will appear.
Press
K
or
L
to select a channel which is not used for
broadcasted between channel 22 and channel 69 in your
area, and
B
to confirm.
Press
MENU
to exit.
Set the TV channel to the RF OUT CHANNEL which was
selected on the VCR/DVD. A picture from the VCR/DVD
will appear on the TV screen. If a picture does not
appear, repeat steps
to
using a different channel
which is not used for broadcasting.
Press
STOP
to stop the tape.
NOTES:
• You may also access the RF OUT CH menu by pressing
and holding
MENU
on the remote control for 3 seconds
during power off until the RF OUT CH menu appears.
• If this unit and your TV are connected using a SCART
cable, the RF converter may be switched off to avoid any
possibility of interference. To switch off the RF converter,
follow
steps and to above
and
press
L
repeat-
edly until “--” appears next to RF OUT CH. Press
B
, then
press
MENU
to exit.
6
4
1
9
8
4
8
7
6
5
4
H97D1ED(EN)v2.qx4 04.9.9 11:53 Page 12
