Sharp DV-HR300U, Service Manual

Page: 24 / 76

24
DV-HR300U
FLOW CHART No.15
LCD display does not light up. Is 5V applied to IC8001 pin 37?
Check STANDBY_5V line.
Is RESET signal released on IC8001 pin 36 (5V)?
Check line between IC501 and IC8001 pin 36.
Is 38KHz oscillation signal output on IC8001 pin 41?
Check R8037 C8016, IC8001 and peripheral circuits.
Are the following signals input to each pin of IC8001?
Check lines between pins of IC501 and IC8001. Check lines between pins of IC8001 and LCD8003 as well as IC8001.
IC8001 pin 44 LCD_DA_IN
IC501 pin 13
→
IC8001 pin 44 FIP_DA_IN
IC8001 pin 43 LCD_CK
IC501 pin 11
→
IC8001 pin 43 FIP_CK
IC8001 pin 42 LCD_CS LCD8003 pin 33 COM1 LCD8003 pin 34 COM2 LCD8003 pin 35 COM3
IC501 pin 12
→
IC8001 pin 42 FIP_CS
Are the following signals input to each pin of IC8003?
Check display tube and main unit.
Check if display tube is damaged (cracked, etc.).
NO
YES
NO
YES
NO
YES
NO
YES
NO
YES
NO
IC8001 pin 33
→
LCD8003 pin 33 COM1
IC8001 pin 34
→
LCD8003 pin 33 COM2
IC8001 pin 35
→
LCD8003 pin 33 COM3
FLOW CHART No.16
Operation keys do not work. Is key switch connected properly?
Check or replace key switch.
Is control voltage properly input to IC501 pin 87 and 88? Check or replace IC501 peripheral circuits.
KE
Y
0
I
N
88pin
KE
Y
1
I
N
87pin
0.
6V
1.
3V
1.
9V
2.
5V
3.
1V
3.
7V
4.
3V
5.
0V
K E Y 0 / K E Y 1
I
N P U T
V O
L T
A
G E
YES
NO
YES YES
POW OPEN/CLOSE
PLAY PLAY PAUSE
CH(-)
CH(+)
DVD
PLAY STOP
HDD
FF
REC PAUSE
REW
REC
TEST
REC STOP
Replace fuse. If the problem persists, refer to Flow chart No.18 "Fuse is blown". Is primary circuit part leaking or short-circuited? (L901, D901, T901, IC901, etc.)
Are voltages on AT17V, AT14V, AT4V and AT-8V normal?
Check rectification circuits of secondary side circuit. Check power failure detection circuit (Q513 and IC506).
Is IC501 pin 1 at "H" level?
Power does not turn on.
Is fuse normal?
Is R903 normal? Is AT5V line normal?
FLOW CHART
No.18
Fuse is blown.
Is primary circuit part leaking or short-circuited? (L901, D901, T901, IC901, etc.)
Check the presence or absence of rectifier diode and short circuit in the rectifier of the secondary circuit. (D9001,9003,9004,9005,9007,9008)
FLOW CHART
No.19
Power does not switch from "OFF" to "ON".
Is AT5V normal?
Is IC501 pin 94 at "H" level?
Is ST_5V (STNDBY 5V) output?
Is IC501 pin 4 at "H" level?
Is P-CON-H line at "H" level?
Are AT_14V and PC_5V (1) output?
Check IC501 peripheral circuits.
Refer to Flow chart No.17 "Power does not turn on".
Check IC501 peripheral circuits.
Check ST_5V SW circuit. (Q9051, Q9052, etc.) Check IC501 peripheral circuits. Check IC508 peripheral circuits.
Check AT_14V line and PC_5V (1) circuit. (Q9053, Q9054, etc.)
Case 1
Case 2
FLOW CHART No.17
YES YES YES YES
YES
YES
NO NO NO NO NO NO NO NO NO NO NO
YES YES YES YES YES