-52
CONTROL CONTENTS
COMMAND
PARAMETER
RETURN
Power ON
Standby mode
(or 30-second startup time)
Power On
P
O
W
R
_
_
_
1
OK or ERR
OK
Power Off
P
O
W
R
_
_
_
0
OK or ERR
OK or ERR
Lamp Status
T
L
P
S
_
_
_
1
0:OFF
,
1:ON
,
2:Re-try
3:Waiting
,
4:Lamp Error
0:OFF
,
4:Lamp Error
Projector Condition
T
A
B
N
_
_
_
1
0:Normal,
1:Temp High,
8:Lamp Life 5% or less,
16:Lamp Burnt-out,
32:Lamp Ignition Failure
0:Normal,
1:Temp High,
2:Fan Error,
4:Lamp Cover Open,
8:Lamp Life 5% or less,
16:Lamp Burnt-out,
32:Lamp Ignition Failure,
64:Temp Abnormally High
Lamp Power Status
T
P
O
W
_
_
_
1
1:On, 2:Cooling 3:Shutting Down
0:Standby
Model Name Check
M
N
R
D
_
_
_
1
XV-Z20000/DT-5000
C1 (COMPONENT1)
I
R
G
B
_
_
_
1
OK or ERR
ERR
C2 (COMPONENT2)
I
R
G
B
_
_
_
2
OK or ERR
ERR
S-VIDEO
I
V
E
D
_
_
_
1
OK or ERR
ERR
VIDEO
I
V
E
D
_
_
_
2
OK or ERR
ERR
DVI
I
R
G
B
_
_
_
3
OK or ERR
ERR
H1 (HDMI1)
I
R
G
B
_
_
_
4
OK or ERR
ERR
H2 (HDMI2)
I
R
G
B
_
_
_
5
OK or ERR
ERR
PC control
A computer can be used to control the projector by connecting an RS-232C cable (null modem, cross type,
commercially available) to the projector. (See page 24 for connection.)
Communication conditions
Set the serial port settings of the computer as follows.
Signal format: Conforms to RS-232C standard.
Parity bit: None
Baud rate*: 9,600 bps / 38,400bps / 115,200bps
Stop bit: 1 bit
Data length: 8 bits
Flow control: None
*Use the same settings for the projector and computer.
Basic format
Send commands from the computer in the following order: command, parameter, and return code. After
processing the command from the computer, the projector sends a response code to the computer.
Info
•
If you are controlling the projector from a computer using RS-232C commands, wait at least 30 seconds
after turning the projector on before sending any commands.
•
When more than one code is being sent, send each command only after the response code for the previ-
ous command from the projector is verifi ed.
•
When using the computer control function of the projector, the projector’s operating status cannot be read
by the computer. There fore, confi rm the status by transmitting the display commands for each adjustment
menu and checking the status with the on-screen display. If the projector receives a command other than a
menu display command, it will execute the com mand without displaying the on-screen display.
Commands
Example: To turn on the projector
Response code format
Normal response
Problem response (communication error or incorrect command)
Command 4-digit
Parameter 4-digit
Command format
RS-232C Specifi cations and Command Settings
C1 C2 C3 C4 P1 P2 P3 P4
O K
Return code (
0DH
)
Return code (
0DH
)
E R R
Return code (
0DH
)
→
←
P
O
W
R
_
1
_
_
O
K
Projector
Computer
