22
R-312AW
R-312AK
COOLING FAN MOTOR REMOVAL
1. Disconnect oven from power supply and remove outer
case.
2. Discharge high voltage capacitor.
3. Disconnect the wire leads from the fan motor.
4. Remove one (1) screw holding the chassis support to
magnetron. And remove chassis support.
5. Release the snap of the main wire harness from the fan
duct.
6. Remove one (1) screw holding the fan duct assembly to
oven cavity.
7. Release the main wire harness from the hole of the fan
duct.
8. Release the fan duct from the waveguide flange.
9. Release the fan duct assembly from the oven cavity.
10.Remove the fan blade from the fan motor shaft according
the following procedure.
1) Hold the edge of the rotor of the fan motor by using a pair
of grove joint pliers.
CAUTION:
*
Make sure that any pieces do not enter the gap
between the rotor and the stator of the fan motor
because the rotor is easily shaven by pliers and
metal pieces may be produced.
*
Do not touch the pliers to the coil of the fan motor
because the coil may be cut or injured.
*
Do not disfigure the bracket by touching with the
pliers.
2) Remove the fan blade from the shaft of the fan motor by
pulling and rotating the fan blade with your hand.
3) Now, the fan blade will be free.
CAUTION:
*
Do not reuse the removed fan blade because the
hole (for shaft) may be larger than normal.
11.Remove the two (2) screws holding the fan motor to the
fan duct.
12.Now, the fan motor is free.
INSTALLATION
1. Install the fan motor to the fan duct with the two (2)
screws.
2. Install the fan blade to the fan motor shaft according the
following procedure.
1) Hold the center of the bracket which supports the shaft
of the fan motor on the flat table.
2) Apply the screw lock tight into the hole (for shaft) of the
fan blade.
3) Install the fan blade to the shaft of fan motor by pushing
the fan blade with a small, light weight, ball peen hammer
or rubber mallet.
CAUTION:
*
Do not hit the fan blade strongly when installed
because the bracket may be disfigured.
*
Make sure that the fan blade rotates smooth after
installation.
*
Make sure that the axis of the shaft is not slanted.
3. Catch three holes of fan duct on three tabs of the
waveguide flange.
4. Install the fan duct assembly to the oven cavity with the
one (1) screw.
5. Insert the snap of the main wire harness to the hole of the
fan duct and insert the main wire harness into the hole of
the fan duct.
6. Install one (1) tab of the chassis support to oven cavity
front plate and install another tab of it to rear plate. And
then screw chassis support to magnetron with one (1)
screw.
7. Connect the wire leads to the fan motor, referring to the
pictorial diagram.
Coil
Gap
Rotor
Bracket
Stator
Groove joint pliers
Shaft
Axis
Stator
These are the position
where should be
pinched with pliers
Rotor
Side View
Rear View
Shaft
Table
Center of
bracket
1. Disconnect oven from power supply and remove outer
case.
2. Discharge high voltage capacitor.
3. Disconnect wire leads from the switches.
4. Remove two (2) screws holding latch hook to oven
flange.
5. Remove latch hook assembly from oven flange.
6. Push outward on the two (2) retaining tabs holding switch
in place.
7. Switch is now free.
At this time switch lever will be free, do not lose it.
Re-install
1. Re-install each switch lever and interlock switch in its
place. The primary interlock switch is in the lower position
and the door sensing switch is in the upper position. The
third door switch is in the lower position at the back of the
latch hook. The monitor switch is in the upper position of
the primary interlock switch.
2. Re-connect wire leads to each switch.
Refer to pictorial diagram.
3. Secure latch hook (with two (2) mounting screws) to
oven flange.
4. Make sure that the monitor switch is operating properly
and check continuity of the monitor circuit. Refer to
chapter "Test Procedure" and Adjustment procedure.
DOOR SENSING / THIRD DOOR/ PRIMARY INTERLOCK AND MONITOR SWITCHES REMOVAL
