background image

40

GENERAL

 INFORMA

TION

User programs

USER PROGRAMS

Program No. 14: Number of copies per account

Program No. 14 is used to display the total number of copies made against
each account number. When program No. 14 is entered, an account number
will appear in the copy quantity display.

If no account number has been registered, “14E” will appear in the copy
quantity display. Press the 

 key. The copier will return to step 2 on page

36.

1.

Use the copy ratio display (

) key to select the account

number.

Use the 

 key to advance through the account numbers.

2.

Press and hold down the 0 key.

The number of copies made against the specified account number will
be displayed. The two higher digits and the three lower digits will
appear alternately while the 0 key is pressed.

Example: 1,234 copies

The upper limit for the number of copies is 49,999. If the number of
copies made reaches 50,000, the number will be reset to 0 and counting
will start again from 0.

3.

Repeat steps 1 and 2 for other account numbers.

4.

To continue with other user programs, press the 

 key

and select another program number. To exit the user
program mode, press the light (

) key.

Downloaded from: 

http://www.usersmanualguide.com/

Summary of Contents for AR-5015






























































Reviews: