Sharp AR-208D Operation Manual Download Page 5 | Manualshive

Page: 5 / 311

background image

3

CAUTIONS

Caution label on the machine

The label (

) in the fusing area of the machine indicates the following:

: Caution, risk of danger
: Caution, hot surface

Cautions on using the machine

Follow the cautions below when using this machine.

Warning:

• The fusing area is hot. Exercise care in this area when removing misfed paper.
• Do not look directly at the light source. Doing so may damage your eyes.

Caution:

• Place the machine on a firm, level surface.
• Do not install the machine in a humid or dusty location.
• When the machine is not used for a long time, for example during prolonged

holidays, turn the power switch off and remove the power cord from the outlet.

• When moving the machine, be sure to turn the power switch off and remove the

power cord from the outlet.

• Do not switch the machine rapidly on and off. After turning the machine off, wait 10

to 15 seconds before turning it back on.

• Do not cover the machine with a dust cover, cloth or plastic film while the power is

on. Doing so may prevent heat radiation, damaging the machine.

• Use of controls or adjustments or performance of procedures other than those

specified herein may result in hazardous radiation exposure.

• The socket-outlet shall be installed near the machine and shall be easily

accessible.

Important points when selecting an installation site

Do not install your machine in areas that are:

• damp, humid, or very dusty
• exposed to direct sunlight
• poorly ventilated
• subject to extreme temperature or humidity changes, e.g., near an air conditioner

or heater.

Be sure to allow the required space around the
machine for servicing and proper ventilation.

8" (20 cm)

4"

(10 cm)

4"

(10 cm)

!AR-208S_208D.book 3 ページ２００７年１２月３日　月曜日　午後３時３３分

«
...
3
4
5
6
7
...
»

Summary of Contents for AR-208D
























































































































































































































































































































Reviews:

No comments

Related manuals for AR-208D

Brand: Xerox Pages: 24

Brand: Oki Pages: 207

Brand: Oki Pages: 56

Brand: Oki Pages: 6

Brand: Oki Pages: 16

Brand: Oki Pages: 323

Brand: Oki Pages: 36

Brand: Oki Pages: 150

Brand: Oki Pages: 341

Brand: Oki Pages: 177

Brand: Oki Pages: 162

Brand: Oki Pages: 20

Brand: Oki Pages: 104

Brand: Oki Pages: 168

Brand: Oki Pages: 28

C9600hnColorSignage

Brand: Oki Pages: 20

C9600hnColorSignage

Brand: Oki Pages: 125

Brand: Oki Pages: 279

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands