background image

30

5

Copier trouble?

TROUBLESHOOTING

If any problem occurs, check the list below before contacting the SHARP service center.

See 
page:

-

12

-

-

13

19

19

32

15

24

15

Solution

Copier does not 
operate.

Blank copies

Copier plugged in?

Problem Possible 

cause

Plug the copier into a grounded 
outlet.

Power switch on?

Turn the power switch on.

Side cover closed 
securely?

Gently close the side cover.

Front cover closed? 

Gently close the front cover and 
then close the side cover.

Is the original placed face 
down on the original 
table?

Place the original face down on 
the original table.

Power save (     ) 
indicator on.

Is the copier in the 
preheat mode?

Press any key to cancel the 
preheat mode.

Adjust the exposure manually.

Adjust the automatic exposure 
level.

Is original image too dark 
or too light?

Is the copier in the 
automatic exposure 
mode?

Is the copier in the auto 
power shut-off mode?

Press the print (

) key to 

cancel the auto power shut-off 
mode.

Copies are too 
dark or too light.

Is the copier in the photo 
exposure mode?

Cancel the photo exposure 
mode.

Dust, dirt, 
smudges appear 
on copies.

Original table or original 
cover dirty?

Clean regularly.

Use a clean original.

Original smudged or 
blotchy?

-

34

10

10

-

26

34

35

Paper misfeeds 
frequently.

25

Striped copies

Is transfer charger clean?

Clean the transfer charger.

Non-standard paper 
used?

Use standard paper. If using 
special papers, feed the paper 
through the bypass tray.

Paper curled or damp?

Store copy paper flat in the 
wrapper in a dry location.

Pieces of paper inside 
copier?

Paper damp?

Remove all pieces of misfed 
paper.

Paper guides in the paper 
tray not set properly?
Too much paper in the 
paper tray or bypass tray?

Set the guides properly 
depending on the paper size.
Remove excessive paper from 
the tray.
Use copy paper within the 
specified range.

Replace with dry copy paper. If 
the copier is not used for a long 
time, remove the paper from the 
paper tray and store it in its 
wrapper in a dry location.

Is the copy paper too 
heavy?

Images rub off 
the copy easily.

Summary of Contents for AR-151





















































Reviews: