background image

38

7

Optional equipment

Before feeding originals in the document feeder tray, be sure to remove any
staples or paper clips from them.

Before placing curled or wavy originals into the document feeding tray, be
sure to flatten them. If not, original misfeeds may result.

The SPF (

) indicator on the operation panel will light up. If this indicator

does not light up, the originals are not properly set or the SPF is not properly
closed.

Badly damaged originals may misfeed in the SPF. It is recommended that
such originals be copied from the original table.

Special originals such as transparency film should not be fed through the
SPF, but should be placed directly on the original table.

          

Original face up

Stream feeding mode

The stream feeding mode allows easy operation of continuous copying from the SPF.
If the stream feeding mode has been enabled using user program No.4, the SPF (

) indicator

will blink approximately 5 seconds after the last original has been fed by the SPF. While this
indicator is blinking, any new originals placed in the document feeder tray will be fed and copied
automatically. If the stream feeding mode has been disabled, the print (

) key must be pressed

each time the originals are set even immediately after completion of a copy run from the SPF.
The default setting of the stream feeding mode is “ON”. See page 20, USER PROGRAMS.

Misfeed in the SPF

An original misfeed may occur at one of three locations: if the misfed original is seen from the
document feeder tray, (A) in the document feeder tray; if the misfed original is not seen from
the document feeder tray, (B) in the exit area or (C) under the feeding roller. Remove the
misfed original following the instructions for each location.

(A)

Open the feeding roller cover and pull the original gently to the left and out from the
document feeder tray. Close the feeding roller cover. Open and close the original
cover to clear the SPF misfeed (

) indicator.

If the misfed original cannot be easily removed, proceed to (C) without pulling the
original forcibly from the document feeder tray.

Feeding roller cover

SINGLE PASS FEEDER (AR-SP3)

Summary of Contents for AR-151





















































Reviews: