Sharp Aquos LC-37D90U, Service Manual

Page: 96 / 208

LC-37D90U
6 – 17
1) Red power LED Remarks
2) Power failure details (Power LED flashes twice and OPC LED flashes)
3) Communication failure details (Power LED flashes 3 times and OPC LED flashe
LED flashing timing chart for error notification.
Error type Power red LED operation (1 cycle) Pins are microprocessor pins.
Lamp failure
Flashes once: Fast L: Off ERR_PNL (pin 73 of IC2002): Abnormal L. Confirmed after 5
consecutive detections at 1 second intervals (detected only
when the backlight is on). Note that after five detection
counts, the lamp cannot be activated except in the monitoring
process. (For the first time, only the inverter is reset, and error
OFF is not activated) Accumulated counts are cleared to 0
when the corresponding setting in the process is made, when
the power is turned on with [CH_DOWN] and [VOL_UP] on
the unit down or after continuous illumination for 3 minutes.
Power failure
Flashes twice Refer to “Power failure details”.
Communication failure with main CPU
Flashes 3 times Refer to “Communication failure details”.
Communication line failure or main CPU communication fail-
ure.
Vsync
IC3301 operation failure.
Flashes 4 times VSYNC (pin 48 of IC2002) failure (uninput). IC3301 operation
failure.
Detected during operation (interruption).
Panel temperature failure
Flashes 5 times If the panel temperature is 60
°
C or more for 15 seconds or
more in a row, CAUTION appears on the OSD (flashes in red
in the lower right screen). If the panel temperature is 60
°
C or
more for 25 seconds or more in a row, error standby is acti-
vated.
Error type Power red LED operation (1 cycle) Pins are microprocessor pins unless otherwise specified.
PS_ON
UR+13V/UR+10V failure
Flashes once AC_DET (pin 31 of IC2002): Abnormal (L), DET_10V (pin 63
of IC2002). UR+10V is not applied.
If error is detected during operation, the power is turned on
again by interrupt handling (instantaneous blackout process-
ing).
EU_POW
D3.3V failure
Flashes twice DET_3V3 (pin 64 of IC2002): Abnormal (L). D3.3V is not
applied (IC9602).
If error is detected during operation, error standby is activated
by polling.
D_POW
UR+6V failure
Flashes 3 times DET_6V (pin 27 of IC2002): Abnormal (L). UR+6V is not
applied.
If error is detected during operation, error standby is activated
by polling.
PANEL_POW
Panel 12V failure
Flashes 5 times DET_PNL12V (pin 57 of IC2002): Abnormal (L). Panel power
is not applied.
If error is detected during operation, error standby is activated
by polling.
Main failure
Flashes 7 times Main microprocessor (IC8101) detection error (FAN error,
etc.)
The details are displayed in “ERROR STANDBY CAUSE” for
the main microprocessor.
Error type Power red LED operation (1 cycle)
Basically, communication logs are analyzed by a bus
monitor or debug print logs are analyzed.
Initial communication
reception failure
Flashes once Initial communication from the main CPU is not received.
(After cancelling the reset, request for the monitor model No.
is not received.)
Communication line failure or main CPU start-up failure.
250ms 1sec
H: On
L: Off
H: On
L: Off
H: On
L: Off
H: On
L: Off
H: On
L: Off
H: On
L: Off
H: On
L: Off
H: On
L: Off
H: On
L: Off
H: On
L: Off
H: On
L: Off