Sharp AL-2021 Service Manual Download Page 94 | Manualshive

Page: 94 / 120

background image

AL-2041 SIMULATION, TROUBLE CODES 10 - 26

L3

00

Content Scanner return trouble
Detail

When the mirror base is returned for the
specified time (6 sec) in mirror initializing
after turning on the power, the mirror home
position sensor (MHPS) does not turn ON.
Or when the mirror base is returned for the
specified time (about 6 sec) after start of
copy return, the mirror home position sensor
(MHPS) does not turn ON.

Cause

Mirror unit abnormality
Scanner wire disconnection
Origin detection sensor abnormality
Mirror motor harness abnormality

Check
and
remedy

Use SIM 1-1 to check the mirror
reciprocating operations.

When the mirror does not return.

Check for disconnection of the scanner wire.
Check the harness and the connector
between the mirror motor and the MCU
PWB.
Replace the mirror unit.
Replace the MCU PWB.

When the mirror does feed.

Use SIM 1-2 to check the mirror home
position sensor.

L4

01

Content Main motor lock detection
Detail

When the main motor encoder pulse is not
detected for 100 msec.

Cause

Main motor unit abnormality
Improper connection or disconnection the
main motor and the harness.
MCU PWB abnormality

Check
and
remedy

Use SIM 25-01 to check the main motor
operations.
Check connection of the main motor
harness/connector.
Replace the main motor.
Replace the MCU PWB.

31

Content Exhaust fan motor lock detection trouble

Detail

The error detection is started after 2 sec
from starting rotation of the exhaust fan
motor.
1) The continuous rotation state of 250ms is

not detected for 1 sec after starting
detection.

2) When the lock sensor (in the exhaust fan)

detects the HIGH level (unstable) after
detection the lock state (stable state).

Cause

Exhaust fan motor connector connection
trouble
Exhaust fan motor trouble
MCU PWB trouble

Check
and
remedy

Exhaust fan motor connector connection
check
Exhaust fan motor replacement
Replace the MCU PWB.

Main
code

Sub

code

Details of trouble

L6

10

Content Polygon motor lock detection
Detail

The lock signal (specified rpm signal) does
not return within a certain time (about 20
sec) from starting the polygon motor
rotation.

Cause

Polygon motor unit abnormality
Improper connection or disconnection of the
polygon motor and the harness.
MCU PWB abnormality

Check
and
remedy

Use SIM 25-10 to check the polygon motor
operations.
Check connection of the polygon motor
harness/connector.
Replace the polygon motor.
Replace the MCU PWB.

U2

00

Content EEPROM read/write error (Serial

communication error)

Detail

EEPROM access process error

Cause

EEPROM abnormality

Check
and
remedy

Check that the EEPROM is properly set.
Use SIM 16 to cancel the trouble.
Replace the MCU PWB.

11

Content Counter check sum error (EEPROM)

Detail

Check sum error of the counter area in the
EEPROM

Cause

EEPROM abnormality

Check
and
remedy

Check that the EEPROM is properly set.
Use SIM 16 to cancel the trouble.
Replace the MCU PWB.

Main
code

Sub

code

Details of trouble

«
...
92
93
94
95
96
...
»

Summary of Contents for AL-2021

























































































































Reviews:

No comments

Related manuals for AL-2021

Brand: Canon Pages: 149

Brand: Canon Pages: 60

Brand: Lanier Pages: 4

Brand: Magicard Pages: 26

Brand: QMS Pages: 194

Brand: Oki Pages: 45

Brand: Lanier Pages: 6

Brand: Tally Pages: 28

Brand: Xerox Pages: 2

Blaster ADVANTAGE

Brand: CognitiveTPG Pages: 20

Brand: IBM Pages: 128

S510 - ScanSnap - Document Scanner

Brand: Fujitsu Pages: 295

Brand: Brother Pages: 93

Brand: Canon Pages: 229

image runner 2520

Brand: Canon Pages: 630

imageCLASS D530

Brand: Canon Pages: 76

IMAGE RUNNER 110

Brand: Canon Pages: 12

imageCLASS D600 Series

Brand: Canon Pages: 113

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands