manualshive.com logo in svg

Sharp AL-2021, Operation Manual, Page: 64 / 91

Share
Download
Sharp AL-2021 Operation Manual Download Page 64

7

7

64

This chapter describes the special functions of this unit. Use these functions as 
needed.

DESCRIPTION OF SPECIAL FUNCTIONS

Toner save mode

Reduces toner consumption by approximately 10%.

Power save modes

The unit has two power save modes of operation: preheat mode and auto power 
shut-off mode.

Preheat mode

When the unit enters the preheat mode, the power save (

) indicator will light up 

and other indicators will remain on or off as before. In this condition, the fuser in 
the unit is maintained at a lower heat level, thereby saving power. To copy from 
the preheat mode, make desired copier selections and press the start (

) key 

using the normal copying procedure.

Auto power shut-off mode

When the unit enters the auto power shut-off mode, the power save (

) indicator 

will light up and other indicators will go out. The auto power shut-off mode saves 
more power than the preheat mode but requires a longer time before starting 
copying. To copy from the auto power shut-off mode, press the start (

) key. 

Then make desired copier selections and press the start (

) key using the 

normal copying procedure.

Auto clear

The unit returns to the initial settings a preset amount of time after the end of job. 
This preset amount of time (auto clear time) can be changed.

Resolution of AUTO & MANUAL mode

You can set the copy resolution used for AUTO and MANUAL (

) exposure 

mode.

Prevention of OC copies when the original cover/SPF is up function

When enabled, this function may help prevent wasteful use of toner that occurs 
when the original cover/SPF is not completely closed.
If the start (

) key is pressed when the original cover/SPF is not completely closed, 

"

" will appear in the display and copying may not take place. If copying does not 

take place, copying can be performed by pressing the start (

) key again, however, 

the scan size set in "Copy effective paper width setting function" (program numbers 
25, 26) will be used.
If the original cover/SPF is completely closed after "

" appears, copying will take 

place at the normal size.

SPECIAL FUNCTIONS

Summary of Contents for AL-2021




























































































Reviews:

No comments