background image

3. Operational panel

(1)

Exposure mode selector key and
indicators

(2)

Light and dark keys and exposure
indicators

(3)

Alarm indicators

1

(4)

SPF indicator

(5)

SPF misfeed indicator

(6)

Copy ratio selector key and copy
ratio indicators

(7)

Zoom indicator

(8)

Copy ratio display (%) key

(9)

Display

(10) ON LINE indicator

(11) Power save indicator

(12) Tray select key

(13) Paper feed location indicators

(14) Zoom keys

(15) Copy quantity keys

(16) Clear key

(17) Print key and ready indicator

1

Drum replacement required indicator
When the drum counter reaches 17,000 copies, the indicator lights up. After 1,000 additional copies are made, the indicator starts
blinking and machine will not-operate (after current job) until a new cartridge is installed.

Misfeed indicator

TD cartridge replacement required indicator
When toner density is lower than a specified level, the TONER DEVELOPER  CARTRIDGE REPLACEMENT indicator lights up
to warn the user.
If toner is not added after approximately 10 sheets are copied, the indicator starts blinking and machine starts to supply
toner.(Toner Developer cartridg replacement indicator keeps lighting up)
If toner density is not back to specific level after two minutes, the READ indicator goes out and Toner Developer indicator starts
blinking, and the copier stops.

2 ON: Indicates that the machine is in the energy saving (pre-heat) mode.

Blink: Indicates that the machine is in the process of resetting from the energy saving mode or just after supplying the power.
OFF: Indicates that resetting from the energy saving mode is completed and that the fusing temperature is in ready state.
The combinations of the above display lamps are as follows: (

 = ON, 

 = OFF)

Lamp

Immediately after power ON

Ready

Copying

Pre-heat lamp

Blink

Ready lamp

Other lamps

Lamp

Energy saving mode (Pre-

heating)

Energy saving mode

(Auto power shut off)

Resetting from energy

saving mode

Copy is started during

resetting from energy

saving mode

Pre-heat lamp

Blink

Blink

Ready lamp

Other lamps

ZOOM

100%

5

1

/

2

MAX.

8

1

/

2

x

5

1

/

2

8

1

/

2

x

8

1

/

2

11

x

8

1

/

2

11

x

8

1

/

2

14

x

8

1

/

2

MIN.

11

x

50%

64%

78%

100%

129%

200%

(1)

(2)

(4)

(11)

(10)

(3)

(5)

(6)

(7)

(13)

(14)

(15)

(16)

(17)

(12)

(9)

(8)

AL-1250

3-2

Summary of Contents for AL-1020































Reviews: