background image

EN-12

Check the following points before calling for 

service.

The unit does not operate

 Check if the circuit breaker has tripped or the 

fuse has blown.

The unit does not cool effectively

 Check the

 fi

lters. If dirty, clean them.

 Check the outdoor unit to make sure nothing 

is blocking the air inlet or outlet.

 Check the thermostat is proper setting. 

 Make sure windows and doors are closed 

tightly. 

The unit does not receive the remote 

control signal

 Check whether the remote control batteries 

have become old and weak.

 Try to send the signal again with the remote 

control pointed properly towards the unit’s 

signal receiver window.

 Check whether the remote control batteries 

are installed properly.

Please call for service when OPERATION 

lamp and TIMER lamp on the unit blink. 

BEFORE CALLING FOR SERVICE

The following conditions do not denote 

equipment malfunctions

UNIT DOES NOT OPERATE

The unit will not operate if it is turned on im-

mediately after it is turned off. The unit will 

not operate immediately after the mode is 

changed. This is to protect the unit. Wait 3 min-

utes before operating the unit.

ODORS

Carpet and furniture odors that entered into the 

unit may  be sent out from the unit.

CRACKING NOISE

This sound is generated by the friction of the 

unit expanding or connecting due to a tempera-

ture change.

A LOW BUZZING NOISE

This is a sound of the unit generating Plasma-

cluster ions.

SWISHING NOISE

The soft, swishing noise is the sound of the 

refrigeran

t fl

owing inside the unit.

MIST SEEN AT INDOOR AIR OUTLET

In cooling operation, this is caused by the dif-

ference between the room air temperature and 

the air discharged.

THE OUTDOOR UNIT DOES NOT STOP

After stopping the operation, the outdoor unit 

will rotate its' fan for about a minute to cool 

down the unit.

ODOR EMITTED FROM THE 

PLASMACLUSTER AIR OUTLET

This is the smell of ozone generated from 

the Plasmacluster Ion generator. The ozone 

concentration is very small, posing no adverse 

effect on your health. The ozone discharged 

into the air rapidly decomposes, and its density 

in the room will not increase.

OPERATING CONDITION

Mode

Indoor 

Temp.

Outdoor 

Temp.

Cooling

Upper limit

32

˚

C

43

˚

C

Lower limit

21

˚

C

21

˚

C

 The built-in safety device may prevent the unit 

from operating when used out of this range.

 Condensation may form on the air outlet if the 

unit operates continuously in the COOL or 

DRY mode when humidity is over 80 %.

AH-PNX11_EN.indd   12

11.3.17   4:02:17 PM

Summary of Contents for AH-PNX11

















Reviews: