29Q-FG1A/1F/1N/1S/1U
3 – 12
CUT OFF, BKGD, SUB-CONT ADJUSTMENT CONTINUED
NO
ADJUSTMENT POINT
ADJUSTMENT CONDITION / PROCEDURE
WAVEFORM OR REMARKS
2
WHITE BALANCE
(1) Receive the internal RF monoscope pattern.
BACKGROUND
(2) Make the picture normal with the remote controller.
I2C BUS
(3) Connect the beam ammeter between terminal of R623.
7500K X : 0.300
Y : 0.310
ADJUSTMENT
(4) Coarsely confirm the beam current to approx. 1.7mA.
18000K X : 0.255
Y : 0.255
(AV-IN SIGNAL)
(5) Receive the window pattern with AV input.
17000K
X : 0.261
Y : 0.261
(6) With the data of DRI-GS and DRI-BS, adjust the color temperature of the 50% white.
12300K X : 0.272 Y : 0.275
(7) Adjust the right dark area of the window to
12300K
with CUT-RS
( With Monolta color thermometer CA-100)
and CUT-GS.
(8) Go back to 50% white area to check colour temperature, if out of range, please
go back to step (6).
* 12300ºK
DRI-GW = "DRI-GS" - 7
DRI-BW = "DRI-BS" - 7
Note 1: Apply this adjustment after aging 30 min or more with the beam current
DRI-GC = "DRI-GS" - 7
1700 ± 50µA.
(On the white or green monocolor screen)
DRI-RC = 25
2: The colour temperature is based on the shipment destination as shown in Table 2.1 at
* 17000ºK & 18000ºK
page 20.
DRI-GW = "DRI-GS" - 7
DRI-BW = "DRI-BS" - 7
3: Adjust DRI-GC/GW, DRI-BC/BW , CUT-RW/C and CUT-GW/C as following DATA,
DRI-GC = "DRI-GS" - 5
after finishing DRI-BS and DRI-GS DATA adjustment.
DRI-RC = 27
* 7500ºK
CUT-RW/C = CUT-RS
DRI-GW = "DRI-GS" - 5
CUT-GW/C = CUT-GS
DRI-BW = "DRI-BS" - 5
DRI-RW = 32 (FIXED), DRI-RS = 32 (FIXED)
DRI-GC = "DRI-GS" - 7
DRI-BC = "DRI-BS"
DRI-RC = 25
(For 7500ºK, 12300ºK, 17000ºK and 18000ºK Condition)
Note 1: Use the window pattern of the signal
generator SX-1006 for adjustment.
3
WHITE BALANCE
(1) The window pattern is received with DVD signal ( component signal).
BACKGROUND
I2C BUS
(2) Apply the adjustment in the same manners as 2 (AV-IN SIGNAL)
However please adjust Y at low bright only to become 0.281 due to the fact that when exiting
service mode, it will drop to 0.275
ADJUSTMENT
and subsequence above.
(DVD SIGNAL)
(DRI-GS-DVD, DRI-BS-DVD, CUT-RS-DVD, CUT-GS-DVD)
Apply the adjustment after the end of 2 (AV-IN SIGNAL).
Note: 1. All of the DRI-GW/C-DVD & DRI-BW/C-DVD can be obtain by using same
50% white
calculation as white balance adjustment above (No.2). CUT-RW/C-DVD
Dark white
and CUT-GW/C-DVD setting data are as follow.
CUT-RW/C-DVD = CUT-RS-DVD
CUT-GW/C-DVD = CUT-GS-DVD
DRI-RW-DVD = 32 (FIXED), DRI-RS-DVD = 32 (FIXED)
DRI-BC-DVD = "DRI-BS-DVD"
4
SUB-BRIGHTNESS
(1) Receive the window pattern with AV input.
ADJUSMENT
(2) Make the image normal with the remote controller.
Note 1: Use "Y" of Minolta color analyzer
(I2C BUS CONTROL)
(3) Select the sub- bright adjustment mode with the remote controller, and adjust the
CA-100 in adjustment
(AV-IN SIGNAL)
right dark white area of the window pattern to
3.0cd ± 0.5cd
Note 2: Use the window pattern of the signal
generator SX-1006 for adjustment.
5
SUB-BRIGHTNESS
(1) Select DVD mode.
ADJUSMENT
(2) Receive the signal of the DVD signal generator . ( Component signal)
(I2C BUS CONTROL)
( Window Pattern)
(DVD SIGNAL)
(3) Make the image normal with the remote controller.
(4) Select the SUB-BRIGHT adjustment mode (DVD) , and adjust the right dark white
area of the window pattern to
3.0cd ± 0.5cd
6
SUB-CONTRAST
(1) Receive the window pattern with AV input.
I2C BUS
(2) Make the image normal with the remote controller.
ADJUSTMENT
(3) Select the SUB-CONTRAST adjustment mode with the remote controller, and
(AV-IN SIGNAL)
adjust 50% white to
130 ± 10cd.
Note : Make sure the TV set already in the RF receiving atate before changing to AV mode
to contimue with this adjustment (no power OFF from the previous adjustment).
7
SUB-CONTRAST
(1) Select the DVD mode.
I2C BUS
(2) Receive the signal of the DVD signal generator. ( Component signal)
ADJUSTMENT
(Window Pattern)
(DVD SIGNAL)
(3) Select the SUB-CONTRAST adjustment mode (DVD) with the remote controller,
and adjust 50% white to
130 ± 10cd.
Note : Make sure the TV set already in the RF receiving atate before changing to AV mode
to contimue with this adjustment (no power OFF from the previous adjustment).
50% white
dark white
Summary of Contents for 9Q-FG1A
