Sharp 32U-F500, Service Manual

Page: 9 / 52

9
32U-F500
32U-F810
SERVICE
NUMBER
DATA
ADJUSTMENT ITEM
INITIAL VALUE
RANGE
ADJUSTMENT CONTENTS
D07 EW PARABOLA 33(21h) 0-63(00h-3Fh) Must be set to “27”
D08 EW TRAPEZIUM 14(0Eh) 0-31(00h-1Fh) Must be set to “0B”
D09 EW CORNER 12(0Ch) 0-15(00h-0Fh) Must be set to “08”
D10 AFC GAIN 2(02h) 0-3 (00h-03h) Must be set to “02”
D11 V EHT 7(07h) 0-7 (00h-07h) Must be set to “04”
D12 H EHT 3(03h) 0-7 (00h-07h) Must be set to “03”
EX1 FAO VOLUME 36(24h) 0-50(00h-32h) Must be set to “24”
EX2 CC-POSITION 33(21h) 0-127(00h-7Fh)
EX3 INT 122(7Ah) 0-255(00h-FFh) Must be set to “7A”
EX4 A-ATT 90(5Ah) 0-127
EX5 TUNER data 0(00h) 0-3(00h-03h) Must be set to “00”
EX6 Think chip-Slice LEVEL 54(36h) 0-255(00h-FFh) Must be set to “36”
OP1 OPTION1 247(F7h) 0-255(00h-FFh) Must be set to “F7” (32U-F810), “F5” (32U-F500)
OP2 OPTION2 249(F9h) 0-255(00h-FFh) Must be set to “F9” (32U-F810), “18” (32U-F500)
OP3 OPTION3 15(0Fh) 0-255(00h-FFh) Must be set to “0F”
M01 INPUT LEVEL 9(09h) 0-15(00h-0Fh) Must be set to “09”
M02 MTS VCO 36(24h) 0-63(00h-3Fh)
M03 FILTER 31(1Fh) 0-63(00h-3Fh)
M04 WIDEBAND 24(18h) 0-63(00h-3Fh)
M05 SPECTRAL 16(10h) 0-63(00h-3Fh)
M06 ANT-B INPUT LEVEL 9(09h) 0-15(00h-0Fh)
M07 ANT-B WIDEBAND 24(18h) 0-63(00h-3Fh)
M08 ANT-B SPECTRAL 16(10h) 0-63(00h-3Fh)
M09 SRS LEVEL 255(FFh) 0-255(00h-FFh) Must be set to “E0”
M10 BBE LEVEL 255(FFh) 0-255(00h-FFh) Must be set to “D9”
M11 SRS&BBE LEVEL 255(FFh) 0-255(00h-FFh) Must be set to “D0”
M12 SRS&BBE OFF LEVEL 255(FFh) 0-255(00h-FFh) Must be set to “E5”
M13 SRS Effect 2(02h) 2-3(02h-03h) Must be set to “02”
M14 BBE-L Effect 8(08h) 0-15(00h-0Fh) Must be set to “0F”
M15 BBE-H Effect 8(08h) 0-15(00h-0Fh) Must be set to “0F”
M16 AGC Level 7(07h) 0-7(00h-07h) Must be set to “01”
M17 BASS Offset 0(00h) 0-31(00h-1Fh) Must be set to “10”
M18 TREBLE Offset 0(00h) 0-31(00h-1Fh) Must be set to “10”
M19 BASS Offset-BBE 0(00h) 0-31(00h-1Fh) Must be set to “11”
M20 TREBLE Offset-BBE 0(00h) 0-31(00h-1Fh) Must be set to “10”
P01 CONTRAST-PIP 50(32h) 0-127(00h-7Fh)
P02 TINT-PIP 41(29h) 0-63(00h-3Fh) Must be set to “29”
P03 COLOR-SAT-PIP 50(32h) 0-127(00h-7Fh)
P04 Y-OFFSET-PIP 9(09h) 0-31(00h-1Fh) Must be set to “09”
P05 HXA-PIP 10(0Ah) 0-255(00h-FFh) Must be set to “0A”
P06 HADJ-PIP 0(00h) 0-15(00h-0Fh) Must be set to “00”
P07 FREE RUN-PIP 11(0Bh) 0-15(00h-0Fh) Must be set to “0B”
P08 TINT-PIP-INPUT 36(24h) 0-63(00h-3Fh) Must be set to “24”
NECESSARY UNNECESSARY
ADJUSTMENT
PART REPLACED
IC2001
IC201
X
Data is stored in IC2102.
The adjustment is needed to compensate for characteristics of parts
including IC201 and MTS level (M01).
Holding down both the VOL-up and CH-up buttons on the TV set at service mode for more than 2 seconds will
automatically write the above initial values into IC2102.
NOTES
X
IC2102
IC3001
CRT
IC1801
Holding down both the VOL-up and CH-up buttons on the TV set in
the service mode for more than 2 seconds will automatically write the
above initial values into IC2102. Then perform a complete adjustment.
Adjust items related to picture tube only.
Adjust items related to MTS only (M01~M20).
Adjust items related to P-IN-P only (P01~P08).
Table - B
X
X
X
X
Table - A