![background image](http://html.mh-extra.com/html/sharp/27dv-cs10/27dv-cs10_service-manual_373823029.webp)
29
27DV-S100
27DV-CS10
Take-up main brake ass'y
Supply main brake ass'y
Tension band ass'y
Tension arm ass'y
Supply reel disk
Take-up reel disk
REEL DISK REPLACEMENT AND HEIGHT
CHECK
• Removal
1. Remove the cassette housing control assembly.
2. Pull the tension band out of the tension arm ass'y.
3. Remove the Supply/Take-up main brake ass'y.
4. Open the hook at the top of the reel disk, and remove
the reel disk.
Note:
Take care so that the tension band ass'y and main brake
ass'y (especially soft brake) are not deformed.
Note:
Check that the reel disk is lower than part A but higher than
part B. If the height is not correct, readjust the reel disk
height by changing the poly-slider washer under the reel
disk.
•
Problems caused by maladjustments
1. Tapes may get scratched.
Note:
When the tension band ass'y is pressed in the direction of
the arrow for removal, the catch is hard to be deformed.
• Reassembly (Supply reel disk)
1. Clean the reel disk shaft and apply grease (SC-141) to
it.
2. Match the phases of reel disk and reel relay gear, and
set the new reel disk.
3. After checking the reel disk height, wind the tension
band ass'y around the reel disk, and insert into the hole
of tension arm ass'y.
4. Assemble the Supply main brake ass'y.
Notes:
1. When installing the reel disk, take due care so that the
tension band ass'y is not deformed and grease does no
adhere.
2. Do not damage the Supply main brake ass'y. Be careful
so that grease does not adhere to the brake surface.
•
Reassembly (Take-up reel disk)
1. Clean the reel disk shaft and apply grease (SC-141) to
it.
2. Align the phase of the reel disk to that of the reel relay
gear and to install a new take-up reel disk onto the
shaft.
3. Check the reel disk height and reassemble the take-up
main brake ass'y.
Note:
1. Take care so that the Take-up main brake ass'y is not
damaged. Take care so that grease does not adhere
the brake surface.
2. After reassembly, check the video search rewind back
tension (see page 32), and check the brake torque (see
page 34).
•
Height checking and adjustment
Note:
1. Set the master plane with due care so that it does not
contact the drum.
2. When putting the master plane, shift the reverse guide
a little in the loading direction. Care must be taken
since excessive shift results in damage.
Figure 1-4.
Figure 1-5.
Master plane
Reverse
guide
Position
pin
Take-up reel disk
Cassette lock
release shaft
Supply reel disk
Figure 1-6.
Summary of Contents for 27DV-CS10
