background image

E11

USEFUL FEATURES (Continued)

TV / Video selection

Switches between TV broadcasts and AV input programmes.

• Each time you press the 

TV/VIDEO

, the input switches between

AV and TV programme.

TV/VIDEO

TV

0

NORMAL

TIMER

FEATURE

CH-SET

PICTURE

4

7

2

8

3

6

9

CH

CH

1

5

TV/VIDEO

Number

buttons

25

SECAM

D/K

AV

This unit is equipped with a microprocessor. Its performance could be adversely affected by external
electrical noise or interference. If this should happen, unplug the unit and plug it in again after a few
minutes.

The following problems do not always indicate a hardware failure. Therefore, please use the
troubleshooting guide below before calling for repair service.
If, after following the guide none of the remedies work, unplug the TV set and call for service.

E12

TROUBLESHOOTING

Quick 
Service 
Check List

Try a new channel to check for possible station 
trouble.

TV not plugged in.
Outlet power OFF.

Antenna not connected to terminal at the back 
of the TV set.

If outside antenna is used, check for broken 
wires.

Check for local interference.

Adjust COLOUR control.

Check batteries in the remote control.

Try fine tuning to correct.

Contrast setting in picture mode might be all 
the way to the minus side. Press the 

NORMAL 

button on the remote control to 

correct.

Increase the volume.

Problems

Remote control does not work.

Bars on screen.

Picture distorted.

Picture rolls vertically.

No colour.

Poor reception on some channels.

Picture weak.

Picture lines or streaks.

Picture ghosting.

Picture blurred.

Sound OK, picture poor.

Picture OK, sound poor.

No picture or sound.

Possible Causes/Remedies

     POWER

 switch of TV not ON.

Turn OFF using the      

POWER

 switch, 

then turn ON again after a minute.

Press 

.

• The channel previously viewed returns to the screen.

Example:

After switching from channel 5 to channel 7, 

 is pressed,

the channel will change to channel 5. Press 

 again to

return to channel 7.

Channel recall

Switches back to the channel you were watching just before the current channel.

5

SECAM

5

SECAM

7

SECAM

7

SECAM

21LF2-RU[EN]

6/14/06, 4:10 PM

7

Summary of Contents for 21LF2-RU









Reviews: