background image

STEP 14: SECURE UPRIGHTS

STEP 15: TOP RAIL INSTALLATION

At this point you can now pull the front of the top

plate (the hooked part) over the stabilizer bar and, after
you are positive that the upright is level, you can now
add the final two screws necessary to secure the
uprights to the pool.  If the uprights are not level, it will
be very difficult to get the top rails to fit together.  It is a
good idea to use a carpenter’s level to check that the
upright is standing perfectly straight.  If the upright is
leaning left or right this is easy to correct before putting
the final two screws into the top plate.

*Top Plate

Top Rail

Upright

Pool Wall

Lift back of top plate
up slightly to snap
over the stabilizer rail

Put front screw of
top plate in loosely

Your pool either has metal top rails, or resin top rails.

Please notice the different hardware that is necessary for the
resin top rail pools.

You should have two people while installing the top

rails.  If a top rail falls in the pool it can cut the liner.  Secure
all metal top rails using # 10 x ½” screws into the
corresponding holes in the top plates.  *Resin top rails
require special #10 x 1” screws that have attached washers.
When installing the top rails do not tighten screws until all
of the top rails have been installed.  This will allow room for
adjustments if necessary on the final few rails that are
installed.  Attach all top rails before the water is more than
12” deep, because if the pool is slightly out of round, you
may have a problem getting the last rail to go on.

DO NOT TIGHTEN UNTIL
ALL OF THE TOP RAILS
HAVE BEEN INSTALLED.

*USE TWO PEOPLE FOR INSTALLATION.

IF A TOP RAIL FALLS INTO THE POOL, 

IT CAN CUT THE LINER.

TOP RAIL

TOP PLATE

RESIN TOP RAIL
INSTALLATION

When a resin top rail pool is
assembled, you must use
special hardware to attach the
resin top rail to the metal top
plate. Please see the diagram 
to the left for assembly.

The special hardware is:

a) A #10 screw that is 1" long.

b) A washer with the screw to  

distribute the pressure 
more evenly.

RESIN TOP RAIL
INSTALLATION

*

Sample Top Plate - Yours may look a little different

Summary of Contents for Above Ground Pool


















Reviews: