Sharkline Above Ground Pool Assembly & Installation Download

Page: 2 / 17

INTRODUCTION:

Congratulations on becoming the owner of a new Sharkline above ground swimming pool. This is the

instruction packet for installing your swimming pool. The following are some helpful hints that you should take

into consideration before installing your pool.

1) Read through the entire instruction booklet before you begin. This will enable you to find out exactly what is

involved with installing your swimming pool before you begin. While you are going through the instructions,

please be aware that all of the diagrams are representative of a 15' x 30' pool. If you have a dif ferent

size pool you will find that your pool has a dif ferent number of uprights than the ones in the diagrams.

2) DO NOT ATTEMPT INSTALLATION IN WINDY OR GUSTY WEATHER. This will not only make

installation more difficult, it may result in damage to your pool before it is completely installed.

3) Although we have broken down the installation into many simple steps, you will probably find that steps one

and two will be the most labor intensive and time consuming steps. Once you have completed those two steps

you should find that the rest of the installation moves along much more quickly .

4) Please be sure to review all safety material and local codes before beginning your installation. There is a yellow

safety envelope packed with your pool. This envelope contains safety material and warning stickers to be

placed on your pool. If you are missing any of these items please contact your dealer or the factory to obtain it.

The warranty is void if all safety precautions are not followed.

5) In the event that you need to make a warranty claim, it is important to know the size and model of your

swimming pool in order to expedite the handling of your claim. Please fill in the information below and keep

for your records.

NAME OF POOL:
SIZE OF POOL:
DATE OF PURCHASE:
NAME OF POOL WALL:
NAME OF LINER:

6) Make sure you have the necessary tools and materials before beginning your installation.

Below is a list of the tools and materials needed.

-Shovel

-Carpenters level and/or transit

-Tape measure

-Patio Blocks (2" x 8" x 16")

-Phillips head screwdriver

-Box cutter (Razor blade)

-Duct tape

-Tamp

-Sand or pool base

-5/16" wrench

-Filter

-1/4" wrench

-Skimmer/Return fitting

Summary of Contents for Above Ground Pool


















Search results

Summary of Contents for Above Ground Pool

Reviews:

Related manuals for Above Ground Pool

Brands by name

Popular brands

Sharkline Above Ground Pool, Assembly & Installation

Search results

Summary of Contents for Above Ground Pool

Reviews:

Related manuals for Above Ground Pool

Brands by name

Popular brands