11
12
AUST: 1800 890 840
NZ: 0800 002 999
NOTE:
The first time that you use the Sonic Duo
™
there may be air in the system causing a delay for
the solution to come out of the spray nozzle. Hold
the spray button down for 5 to 10 seconds until you
see the solution come out.
6
Lightly step on the back of the scrubbing head to
release the handle and move the agitating Sonic
Duo
™
back and forth over the area to clean tough,
dried on stains faster and easier. Repeat until the
entire floor surface has been cleaned. No rinsing is
required.
WARNING: Never stand on the Sonic Duo
™
.
7
Press the Spray Button to apply solution onto the
floor that is to be cleaned.
(Fig. 28)
8
If the Reusable Bottle is empty, you can refill it at
any time as long as the Sonic Duo
™
is unplugged
from the outlet.
IMPORTANT:
Never leave the Sonic Duo
™
with a
damp/wet cleaning pad on any floor surface for any
amount of time as this may damage the floor.
9
Once finished, step on the tag of the Hard Floor
Cleaning Pad and lift the unit to remove the pad from
the Sonic Duo
™
.
(Fig. 29)
Using Your Sonic Duo
™
Carpet, Wood & Hard Floor Cleaner - cont.
IMPORTANT:
Make sure the floors are swept or
vacuumed before using the Sonic Duo
™
.
4
Twist the quick release cord holder to unwrap the
power cord completely.
(Fig. 25)
Plug into an electrical outlet and slide the “On/Off”
button down to turn the Sonic Duo
™
on. Use “I Low”
setting for hard floor cleaning.
(Fig. 26)
5
Make sure that the Hard Floor Cleaning Pad is
attached to the Sonic Duo
™
. This pad has a “Green”
trim and the tag says “Hard Floor Cleaning Pad”.
Attach the side of the Cleaning Pad with the tag to
the back of the Sonic Duo
™
.
(Fig. 27)
Frequently Asked Questions
Q.
My Sonic Duo
™
leaves a foam on hard floors.
A.
The Sonic Duo
™
Hard Floor Cleaning Pad is likely
too saturated. Replace it with a clean, dry pad.
Q.
My floors appear cloudy after cleaning.
A.
The Sonic Duo
™
Hard Floor Cleaning Pad may be
dirty. Change the pad.
OR
A.
The Sonic Duo
™
Hard Floor Cleaning Pad was
washed with a powder detergent and may be
damaged and require replacement. Never use
powder detergents. Only use liquid detergent to
launder the cleaning pads.
OR
A.
The Sonic Duo
™
may have been left in the same spot
for too long with a wet cleaning pad. Never leave the
unit with a wet pad in one spot for too long.
OR
A.
This may be leftover from past cleaners that were
used on the floor surface. Use the Sonic Duo
™
a
few more times and see if the leftover cloudiness
is removed. If this does not work, we suggest
rinsing the floor with water and letting it dry. One
or more rinses generally removes the residue. A
more stubborn case may require you to rinse the
floor with a mix of one part vinegar to 2 parts water.
Then use the Sonic Duo
™
again with a clean pad.
fig. 28
fig. 25
fig. 24
IMPORTANT:
When cleaning, do not use the Sonic Duo
™
without attaching a Hard Floor Cleaning Pad and adding
the diluted cleaning solution to the Reusable Bottle first.
When polishing, do not use the Sonic Duo
™
without
attaching a Hard Floor Polishing Pad.
Cleaning Your Hard Floors:
1
To remove the Reusable Bottle, hold it and pull it up
to remove from the unit.
(Fig. 22)
2
Remove the “Green” bottle cap. Add 1 part of the
Sonic Activated Wood & Hard Floor Cleaner solution
to 7 parts water into the Reusable Bottle. Use the
measuring marks on the Reusable Bottle for easy
measuring and filling.
(Fig. 23)
Always fill with cold
water first up to the “Water Fill Line” and then the
add the cleaning solution up to the “Solution Fill
Line” to avoid foaming and to ensure accuracy.
3
Screw the bottle cap on tightly and insert the
Reusable Bottle into the unit upside down. Push it
down to make sure that it is well inserted. You will
hear an audible “Click” when the Reusable Bottle is
inserted properly.
(Fig. 24)
IMPORTANT
: Do not use on unsealed wood or
unglazed ceramic floors. Do not use on wood or
tile floors that are highly worn, unfinished or have
a wax or oil finish. Surfaces that have been treated
with wax or some no wax floors may be damaged by
the cleaning and polishing solutions therefore it is
always recommended to test an isolated area of the
surface to be cleaned before proceeding. You should
always check the use and care instructions from the
floor manufacturer.
fig. 22
fig. 23
fig. 26
fig. 29
fig. 27
