background image

13

www.pressandrefresh.co.uk

Using Your Press & Refresh

 - cont.

Care of Your Press & Refresh

Troubleshooting Guide

Cleaning & storing

1

   Turn the garment steamer off  

“O”.

2

   Unplug the appliance from the 

electrical outlet.

3

   Let the appliance cool 

completely for approximately  
30 minutes.

4

   Empty the water from the  

water tank.

5

   Wipe the exterior of the 

garment steamer with a damp 
cloth and wipe dry if needed. 

9

   Hand wash the bonnet frame 

in cold water with a mild 
detergent and let air dry 
completely before using again. 
Do not dry in clothes dryer.

10

  To re-attach the frame, gently 

snap the frame over the steam 
nozzle and press gently to lock 
into place (

Fig. 1

).

PROBLEM

POSSIBLE REASONS 

SOLUTIONS

There is no
steam.

The steamer is not turned on. 

There is not enough  
water in the unit.

Verify that the blue light on the unit is lit. If not, 
check that the unit is plugged in and the on/off 
button is raised and in the on “I” position. 

Verify that the water tank is at least half way full 
or fill to the max fill line.

The nozzle leaves 
water drops on the 
garment.

You are not using the steam 
bonnet.

The steam bonnet is  
too wet.

The frame has condensation.

The small steam bonnet frame must be in place  
at all times during usage. 

The bonnet prevents water drops being left on 
the garment and to removes impurities from your 
water.

Let the unit cool for 30 minutes, remove the 
steam bonnet and let it dry out before using 
again or replace with a new bonnet frame.

Let the appliance cool and wipe the frame off.

6

   Bundle up the power cord and 

secure it with the VELCRO

®

 

strap that is attached to the 
power cord. Always store your 
appliance in a cool, dry area.

Care & use of the small steam 
bonnet frame

7

  

The steam bonnet is attached 
to a frame and helps filter 
impurities from your water. 
It might become slightly 
discolored over time.

8

   Let the steamer cool completely 

before removing. Gently pull on 
either side of the frame and lift 
off of the nozzle.

Fig. 1

Summary of Contents for GS500UKJR

















Reviews: