10
11
EN-US
Programming
- 1 press on the «NORMAL» button = change to the next level
indicated by a beep. This will increase the amount of inco-
ming water by two seconds.
- 1 press on the «ECO» button = change to the previous level
indicated by a beep. This will decrease the amount of inco-
ming water by two seconds.
When the modification reaches the maximum or minimum
level, the buzzer stops beeping.
Description of the programming levels:
*S = operation of the solenoid valve (filling with clean water)
*P = pump operation (dilution and discharge)
Normal Cycle
S*
S+P*
S
S+P
S
S+P
Basic level
6 s
1 s
3 s
1 s
3 s
1 s
level +1
8 s
1 s
3 s
1 s
3 s
1 s
level +2
10 s
1 s
3 s
1 s
3 s
1 s
level +3
12 s
1 s
3 s
1 s
3 s
1 s
level +4
14 s
1 s
3 s
1 s
3 s
1 s
• To exit the programming mode automatically: no keys pres-
sed for 5 seconds = the green led turns on.
Note : The water consumption programmed remains in the
memory even after the unit has been disconnected from the
power supply.
6.2 MANAGEMENT OF THE BLACK WATER TANK
STATUS
ELECTRONIC KEYBOARD
USE
BUZZER
LED
Buzzer
CAPTEUR
2
CAPTEUR
1
Sensor 1 : OFF
Sensor 2 : OFF
OFF green
OFF yellow
OFF
Normal
CAPTEUR
2
CAPTEUR
1
Sensor 1 : ON
Sensor 2 : OFF
ON green
ON yellow
OFF
Normal
CAPTEUR
2
CAPTEUR
1
Sensor 1 : ON
Sensor 2 : ON
OFF green
ON
flashing red
(«FULL»
message
visible)
4 beeps
when a
key is
pressed.
3 extra cycles
allowed.
Control panel
then is locked
until the tank
is emptied.
Override of the system when 3rd status is reached
Pressing «NORMAL» for 5 seconds will return cycles to nor-
mal operation.
Attention: Prolonged use of the toilet when black
water tank is full can lead to overflow.
LED
yellow/red
LED
green
7.2 WINTERIZING
• In the event of a long period without use, rinse the bowl
then drain using the «EMPTY» button.
• Switch off the water and electricity supplies.
• Take the necessary measures to prevent damage caused
by freezing.
• If using antifreeze, use only RV-antifreeze.
8. FAULT FINDING GUIDE
DISCONNECT ELECTRICAL POWER BEFORE
WORKING ON THE UNIT !
FAULT
DETECTED
PROBABLE CAUSES
REMEDIES
The cycle
proceeds
correctly, the
motor turns but
water in the
bowl empties
slowly or not
at all.
The evacuation is
clogged.
Dismount and clean the
discharge pipe.
The cycle
proceeds
correctly, but
some water
remains in the
bowl after a
cycle.
The height of
evacuation is too
important.
Modify the installation.
The discharge pipe
is pinched.
Check the route of the
discharge pipe.
The motor
rattles or
crunches.
Foreign body into
the bowl.
• Disconnect the motor
supplies.
• Close water admission.
• Remove the motor unit.
• With a hook, withdraw
all the matters being able
to obstruct the rotation of
macerator.
• With a tool, turn the
turbine in the 2 directions
until rotation is free.
• Re-connect the motor
supplies and press on
the pneumatic contactor
to control the correct
operation of unit.
• Open water supply.
If the macerator remains
blocked, we recommend to
call the SFA-Saniflo after-
sales service.
After the
button on the
control panel
has been
pressed, the
cycle does not
start.
Faulty program.
Faulty control
panel.
Replace the control panel
Call the SFA-Saniflo after-
sales service.
The cycle starts
but little water
runs in the
bowl.
The inlet filter of
the solenoid valve is
clogged.
Clean the filter of the
solenoid valve.
The water feed
pipe is pinched.
Check the water admission
pipe.
The cycle
engages but
water does not
run in the bowl
The stop valve is
closed.
Open the stop valve.
The solenoid valve
is defective.
Change the solenoid valve.
7. CLEANING/MAINTENANCE
SN4 071
can be used like any normal toilet and does not re-
quire any particular maintenance.
7.1 CLEANING
• For cleaning, use normal sanitary products.
• Do not use aggressive chemicals (such as acetone, pure
bleach, etc.) that could damage the material of the bowl.
• Use a suitable standard toilet brush; do not use scouring or
abrasive pads.
