background image

Copyright ©2009, Seymour Products LLC, 

www.seymourav.com

, All rights reserved. 

 

 

 
 
 
 
 
 
 
 

 
 
 
 
 
 
 
 
 
 
 
 

 

Electric Screen Contents ................................................................................................................... 2 
Electric Screen Installation Instructions.............................................................................................. 5 

Wall Mount..................................................................................................................................... 5 
Ceiling Mount................................................................................................................................. 6 

Gen4 4-wire and Somfy

®

 Motor Control Options ................................................................................ 9 

Gen4 4-wire wall switched ONLY................................................................................................... 9 
Gen4 4-wire motor control box options........................................................................................... 9 
Gen4 4-wire connection ............................................................................................................... 10 
Gen4 4-wire IR control ................................................................................................................. 10 
Gen4 4-wire RF control................................................................................................................ 11 
Gen4 4-wire motor control box wall-switched, or relay controlled ................................................. 11 
Gen4 nonstandard options........................................................................................................... 12 
Somfy control............................................................................................................................... 12 
Somfy 4-connector splitter ........................................................................................................... 12 
Somfy IR control .......................................................................................................................... 12 

Somfy RF control ............................................................................................................................. 12 
Gen4 Standard RF Motor Limits Setting (RF motors with LED dongle) ............................................ 13 

Gen4 Limits Setting Flowchart ..................................................................................................... 14 

Gen3 Standard RF Motor Limits Setting (RF motors without LED dongle) ....................................... 15 

Gen3 Limits Setting Flowchart ..................................................................................................... 16 
Gen4 RF remote replacement...................................................................................................... 17 

Troubleshooting ............................................................................................................................... 17 

Waves.......................................................................................................................................... 17 
“Ca-chunck” clanking sound when bar goes into case ................................................................. 18 
Motor bogs down in the upper position before stopping ............................................................... 19 
RF remote doesn’t work ............................................................................................................... 19 

 

GET THE SCREEN,

 

KEEP THE SOUND™

 

Summary of Contents for Center Stage XD




















Reviews: