background image

3OHDVHUHIHUWRWKHSURJUDPPLQJPDQXDOLQFOXGHGLQ&'

5GVVKPIWRVJGUQHVYCTG

(%%+PHQTOCVKQP

This device complies with part 15 of the FCC Results. Operation is subject to 
the following two conditions:
           (1) This Device may not cause harmful interface, and
           (2) This device must accept any interference received, including     
                 interference that may cause undesired operation.

0QVG

This equipment has been tested and found to comply with the limits for 
CLASS B digital device, pursuant to Part 15 of FCC Rules. These limits are 
designed to provide reasonable protection against harmful interference when 
the equipment is operated in a commercial environment. This equipment 
generates, uses and can radiate radio frequency energy and, if not installed 
and used in accordance with the instuctions, may cause harmful interference 
to radio communications. However, there is no guarantee that interference 
will not occur in a particular installation. If this equipment does cause harmful 
interference to radio or television reception, which can be determined by 
turning the equipment off and on, the user is encouraged to try correct the 
interference by one or more of the following measures:

      1.1. Reorient or relocate the receiving antenna.
      1.2. Increase the separation between the equipment and receiver.
      1.3. Connect the equipment into an outlet on a circuit different from
            that to which receiver is connected.
      1.4. Consult the dealer or experienced radio/TV technician for help.            

9#40+0)
%JCPIGU QT OQFKHKECVKQPU PQV GZRTGUUN[ CRRTQXGF D[ VJG OCPWHCEVWTGT
EQWNFXQKFVJGWUGThUCWVJQTKV[VQQRGTCVGVJGGSWKROGPV

ǁ

%GTVKHKECVKQP

%#76+10
#PVGPPCUJCNNDGOQWPVGFKPUWEJCOCPPGTVQOKPKOK\GVJGRQVGPVKCNHQTJWOCP
EQPVCEVFWTKPIPQTOCNQRGTCVKQP6JGCPVGPPCUJQWNFPQVDGEQPVCEVGFFWTKPI
QRGTCVKQPVQCXQKFVJGRQUUKDKNKV[QHGZEGGFKPIVJG(%%TCFKQHTGSWGPE[GZRQUWTG
NKOKV

Summary of Contents for LUKHAN LK-P21B















Reviews: