SEWOO LK-P SERIES Command Manual Download Page 18

Page: 18 / 48

ESC/POS Command Manual

X 24).

[Reference]

ESC E

[Name]

Turn emphasized mode on/off

[Format]

ASCII

ESC

Hex

Decimal

[Range]

0≤

≤255

[Description]

Turns emphasized mode on or off.

When the LSB of

is 0, emphasized mode is turned off.

When the LSB of

is 1, emphasized mode is turned on.

[Details]

Only the least significant bit of

is enabled.

This command and ESC! Turn on and off emphasized mode in the same way. Be careful when this

command is used with ESC!.

[Default]

= 0

[Reference]

ESC !

ESC G

[Name]

Turn on/off double-strike mode

[Format]

ASCII

ESC

Hex

Decimal

[Range]

0≤

≤255

[Description]

Turns double-strike mode on or off.

When the LSB of

is 0, double-strike mode is turned off.

When the LSB of

is1, double-strike mode is turned on.

[Details]

Only the lowest bit of

is enabled.

Printer output is the same in double-strike mode and in emphasized mode.

[Default]

= 0

[Reference]

ESC E

ESC J

[Name]

Print and feed paper

Summary of Contents for LK-P SERIES

















































Search results

Summary of Contents for LK-P SERIES

Reviews:

Related manuals for LK-P SERIES

Brands by name

Popular brands

SEWOO LK-P SERIES, Command Manual

Search results

Summary of Contents for LK-P SERIES

Reviews:

Related manuals for LK-P SERIES

Brands by name

Popular brands