SEW-Eurodrive MOVI-C UHX45A Series Manual Download Page 87

Page: 87 / 92

Index

Accessories ......................................................... 20

Additional documentation .................................... 13

Arrangement of the axis modules within the axis

system ............................................................ 22

Assign PROFINET device name of the MOVI-C

CONTROLLER............................................... 60

Auto-crossing ...................................................... 40

Auto-negotiation .................................................. 40

Checking communication via process data ......... 73

Communication interfaces ................................... 17

Engineering .................................................... 18

EtherCAT

/SBusPLUS ................................... 18

Fieldbus.......................................................... 18

Compact controller

Elements ........................................................ 23

Installing a module ......................................... 24

Mounting the carrier plate............................... 23

Removing the carrier plate ............................. 23

Technical data ................................................ 82

Voltage supply................................................ 35

Configuration

EtherCAT

/SBusPLUS stations...................... 51

Fieldbus stations ............................................ 56

Configuring EtherCAT

/SBusPLUS stations ....... 51

Configuring fieldbus stations ............................... 56

Connection

Engineering PC .............................................. 37

EtherCAT

/SBusPLUS master ....................... 38

Fieldbus slave ................................................ 39

Content of the manual ......................................... 13

Designated use ................................................... 10

Device description file ......................................... 57

Device replacement............................................. 78

Device topology example .................................... 50

DHCP

Description ..................................................... 49

Dimension drawing .............................................. 85

Dynamic Host Configuration Protocol, see DHCP

....................................................................... 49

Electrical installation ............................................ 12

Safety notes ................................................... 12

Electrical installation, protective separation ........ 31

Embedded safety notes......................................... 7

Engineering interface .......................................... 18

Engineering PC

Connect to the local network .......................... 51

Connection to MOVI-C

CONTROLLER ........ 51

Setting the IP address parameters................. 51

Engineering software........................................... 19

EtherCAT

/SBusPLUS

Connection master ......................................... 38

Interface ......................................................... 18

Ethernet net

Ethernet switch............................................... 40

Network topologies......................................... 40

Shielding and routing bus cables ................... 31

Ethernet switch .................................................... 40

Auto-crossing ................................................. 40

Auto-negotiation ............................................. 40

Exclusion of liability ............................................... 8

Fieldbus interface ................................................ 18

Setting ............................................................ 68

Functional description

MOVI-C

CONTROLLER ............................... 14

Terminals L carrier ......................................... 34

Terminals MOVI-C

CONTROLLER .............. 32

Functional safety technology

Safety note ..................................................... 11

GSDML file, see device description file ............... 57

Hazard symbols

Meaning............................................................ 7

24777730/EN – 01/18

Manual – MOVI-C

CONTROLLER advanced with PROFINET IO Fieldbus Interface

Summary of Contents for MOVI-C UHX45A Series





























































































Search results

Summary of Contents for MOVI-C UHX45A Series

Reviews:

Brands by name

Popular brands

SEW-Eurodrive MOVI-C UHX45A Series, Manual

Search results

Summary of Contents for MOVI-C UHX45A Series

Reviews:

Brands by name

Popular brands