SEW-Eurodrive MOVI-C UHX45A Series Manual Download Page 37

Page: 37 / 92

Installation notes

Electrical installation

Manual – MOVI-C

CONTROLLER advanced with PROFINET IO Fieldbus Interface

4.3.4

Engineering PC connection

The MOVI-C

CONTROLLER is connected to the X80 engineering interface (RJ45

connector) with the engineering PC or other network stations (e.g. visualization sys-
tems). The communication is realized via Ethernet.

The device is connected to the other network stations, using a category 5, class D
twisted-pair cable in accordance with IEC 11801, edition 2.0.

L/A

X80

X40

US1

X85

L/A

X41

L/A

UHX45A-N

9007220297970187

INFORMATION

According to IEEE 802.3, 200 Edition, the maximum cable length for
10 MBaud/100 MBaud/100 MBaud Ethernet (10BaseT/100BaseT/1000BaseT)
between 2 network nodes is 100 m.

24777730/EN – 01/2018

Summary of Contents for MOVI-C UHX45A Series





























































































Search results

Summary of Contents for MOVI-C UHX45A Series

Reviews:

Brands by name

Popular brands

SEW-Eurodrive MOVI-C UHX45A Series, Manual

Search results

Summary of Contents for MOVI-C UHX45A Series

Reviews:

Brands by name

Popular brands