SEW-Eurodrive MOVI-C UHX45A Series Manual Download Page 39

Page: 39 / 92

Installation notes

Electrical installation

Manual – MOVI-C

CONTROLLER advanced with PROFINET IO Fieldbus Interface

4.3.6

CAN system bus connection

In preparation

4.3.7

Connecting the fieldbus slave

The MOVI‑C

CONTROLLER serves as fieldbus slave for the PLC (fieldbus master).

The communication is realized via Ethernet.

The MOVI‑C

CONTROLLER is connected to the Ethernet network via the following

terminals:

•

X40 (RJ45 connector)

•

X41 (RJ45 connector)

The device is connected to the other network stations, using a category 5, class D
twisted-pair cable in accordance with IEC 11801, edition 2.0.

L/A

X80

X40

US1

X85

L/A

X41

L/A

UHX45A-N

X40

L/A

X41

L/A

9007220298082955

INFORMATION

According to IEEE 802.3, 200 Edition, the maximum cable length for
10 MBaud/100 MBaud Ethernet (10BaseT/100BaseT) between 2 network nodes is
100 m.

24777730/EN – 01/2018

Summary of Contents for MOVI-C UHX45A Series





























































































Search results

Summary of Contents for MOVI-C UHX45A Series

Reviews:

Brands by name

Popular brands

SEW-Eurodrive MOVI-C UHX45A Series, Manual

Search results

Summary of Contents for MOVI-C UHX45A Series

Reviews:

Brands by name

Popular brands