Setec Power DC Quick EV Charger Installation Manual Download Page 4

IMPORTANT SAFETY AND GROUNDING
INSTRUCTIONS Safety and Compliance

1.Read the manual before installation or usage of device.
2.Do not put tools, material or body parts into the electric vehicle connector.

3.Do not use the DC Quick EV Charger if the chassis, power cord or charging cable are

frayed, have broken insulation, or any other signs of damaged.

4.Do not install or use the DC Quick EV Charger if the enclosure is broken, cracked, open or

has any other indications of damage.

5.The DC Quick EV Charger should be installed only by a qualified technician.

6.Make sure that the materials used and the installation procedures follow local building

codes and safety standards.

7.The information provided in this manual in no way exempts the user of responsibility to

follow all applicable codes or safety standards.

8.The manufacturer is not responsible for physical injury, damage to property or

equipment caused by the installation of this device.

9.This document provides instructions for the DC Quick EV Charger and should not be used

for any other product. Before installation or use of this product, you should review this

manual carefully and consult with a licensed contractor, licensed electrician, or trained

installation expert to make sure of compliance with local building codes and safety

standards.

Grounding Instructions

An equipment grounding conductor or a grounded, metal, and permanent wiring system is

required for the DC Quick Charger connection. This should be run with circuit conductors and

connected to the equipment grounding bar or lead on the DC Quick Charger.

Notes:

Do not install charging station in locations where it may be exposed to direct

sunlight and inclement weather. Recommend waterproof shed for EV

charger.

If the charging station is to be stored, keep it in its original packaging in an

appropriate place:

· On dry base ground

· Sheltered from dust, inclement weather, and sunlight;

· storage temperature: -30°C to 70°C

· Humidity: 5–95%

Summary of Contents for DC Quick EV Charger

























Reviews: