background image

3019 Alvin DeVane Blvd.
Ste. 560
Austin, TX 78741
Phone: (650) 965-8020

CORPORATION

®

TECH SUPPORT: 650-965-8020 ext. 703

Questions or technical issues? Please call:

Page      of

2

7

LiberatorMAX Headset

Operating Instructions

1) Power-Up

Turn Volume Control clock-wise to turn on headset

1 to 3 audible beeps will indicate level of battery charge when 
headset is powered up (1 beep = low, 3 beeps = high)

Headset will be on channel last used

Headset will search for an existing “network” to join, or create 
its own network if one isn’t found

LED Status Indicator will start Yellow, then turn Green

Headset will begin sending/receiving audio within 6 seconds

There will be a verbal (spoken) indication of the current channel

Volume Control will adjust received audio volume

As other headsets on same channel are turned on, they will join 
the network if they are on the same channel

2) Mobile Radio PTT / Mic Mute / Channel Change Button

On CSB-900MAX and CSB-902MAX headsets, the lower 
button on the right-hand cup functions as a Push-To-Talk 
switch for the mobile radio connected to the Base unit. Press 
to transmit, release when done.

On the CSB-901MAX and CSB-905MAX headsets, the lower 
button on the right-hand cup functions as a Microphone Muting 
switch: press once to mute the mic, there will be two audible 
beeps; press again to un-mute the mic, there will be two beeps 
at a different pitch.

3) Channel Change – All Fire Wireless Headsets

To change channels, hold down both lower buttons on the left-
hand and right-hand cups for 5 seconds. The headset will 
increment by one channel and give a verbal announcement of 
the current channel. The buttons can then be released. If the 
buttons are held down, the headset will advance the channel 
once each second.

All headsets must be on the same channel to remain 
connected as a network (unless the operator is intending to 
join another network).

NOTE:

If using a Portable Radio with the headset, it must be 

turned off or disconnected when changing channels, or it will 
be inadvertently keyed to transmit.

(continued on next page)

LiberatorMAX Fire Wireless Headsets
CSB-900MAX / CSB-902MAX Radio Transmit
CSB-901MAX / CSB-905MAX Intercom-Only
USERS GUIDE

7/8/19 SBH

LiberatorMAX_Fire_User_Guide_REV_A.pdf

Summary of Contents for LiberatorMAX CSB-900MAX








Reviews: