Sermatec SMT-100kWh User Manual Download Page 7

Page: 7 / 66

SHANGHAI SERMATEC ENERGY TECHNOLOGY CO.,LTD

- 4 -

2 Safety instructions

2.1 Safety instructions

This section describes general safety precautions that need to be

taken into account when operating industrial and commercial energy

storage systems. For the safety instructions in the specific use and

maintenance procedures, please refer to the corresponding chapter

warning instructions.

Danger

Touching contacts or terminals which connected to the power grid or

inside the equipment may cause electric shock to death!

Do not touch the terminals or conductors connected to the grid

circuit.

Pay attention to all instructions or safety instructions regarding

connection to the power grid.

Danger

Fatal high voltage inside the product!

Heed and observe the warning signs on the product.

Observe the safety precautions listed in this manual and other

Summary of Contents for SMT-100kWh



































































Search results

Summary of Contents for SMT-100kWh

Reviews:

Related manuals for SMT-100kWh

Brands by name

Popular brands

Sermatec SMT-100kWh, User Manual

Search results

Summary of Contents for SMT-100kWh

Reviews:

Related manuals for SMT-100kWh

Brands by name

Popular brands