www.SereneLifeHome.com
2
www.SereneLifeHome.com
6
www.SereneLifeHome.com
7
Accessory Name
Qty
Accessory Name
Qty
Allen Key M8
1
Screw
Foot M6*30
2
Allen Key M6
1
Washer
2
Screw M6*20
2
Screw M6*8
4
Wheel
2
Screw M8*120
3
S/S Tube
3
Spring Washer ø8.5
3
Spring Washer ø6.2
4
Spring Washer ø8.2*ø16
3
Screw M6*12
2
PARTS DESCRIPTIONS:
ACCESSORIES PACK CHECK LIST:
INSTALLATION
1. Take out all the components form the cartons.
2. As shown in figure A, turn over the Base and Base Cover, let Screw M6*12(#5)
fix the Wheels(#3) through the small holes on the Base.
3. Fix Screw Feet M6*30(#22) onto the Screw Board, and adjust it into the same
level as the Wheels.
4. Put Spring Washer ø8.5(#24) and Spring Washer ø8.2*ø16(#25) into the Screw
M8*120(#23) then get through the Base(#4), Base Cover(#6), S/S Tube(#26).
Use the provided Allen Key M8 to fasten the Screw M8*120
（
#23
）
with Foot Bracket.
5. Turn over the Heater Body. Put the Base on it. Pull out the Power Cord
（
#9
）
through the Base Cover
(
#6
)
and Base
(
#4
).
6. Let the Base Brackets
(
#7
)
match with the holes on the Base Cover (#6) and
Base (#4). Then fix the Base Brackets with the Washers (#2) and Screw M6*20 (#1)
with the provided Allen Key M6.
7. Fix the Power Cord with the Cord Clip (#10).
8. Put Table Top on top of the Heater Body. Make sure the screw holes on Table
Fixture are matching the holes on Top Steel Board. Fix Table Top onto Heater
Body with 4 Screws M6*8 (#15) and Spring Washers ø6.2 (#14)
OPERATIONS:
1. Plug in the unit to a socket. Make sure the power supply is same as rated.
If the heater’s indicator light starts flashing, it means it's in standby status.
2. Press Mode button on the control panel or remote control to switch to low
power or high power as desired. Indicator Light – Green light & Red light will
light up accordingly.
3. Press OFF button on the control panel or remote control to shift the heater to
Standby mode.
GROUNDING INSTRUCTIONS:
This heater is for use on 120 volts. The cord has a plug as shown at A in Figure
below. An adapter as shown at C is available for connecting three-blade grounding-
type plugs to two-slot receptacles. The green grounding lug extending from the
adapter must be connected to a permanent ground such as a properly grounded
outlet box. The adapter should not be used if a three-slot grounded receptacle is
available.
No.
Part Name
No.
Part Name
No.
Part Name
1
Screw M6*20
11
Table Top
21
Remote Controller
2
Washer
12
Table Fixture
22
Screw Foot M6*30
3
Wheel
13
Top Steel Board
23
Screw M8*120
4
Base
14
Spring Washer ø6.2
24
Spring Washer ø8.5
5
Screw M6*12
15
Screw M6*8
25
Spring Washer ø8.2*ø16
6
Base Cover
16
Control Panel
26
S/S Tube
7
Base Bracket
17
Power Indicator Light
27
Foot Bracket
8
Heater Body
18
OFF Buttom
9
Power Cord
19
Receiver
10
Cord Clip
20
Mode Button
Grounding Methods
Metal Screw
Ground cover
Outlet Box
Grounding Pin
A
B
Grounding Pin
Grounding Means
C
D
ADAPTER
