SEPTENTRIO AsteRx-U3 User Manual Download Page 61

Page: 61 / 83

6.2. AIM+: USING THE SPECTRUM ANALYZER TO

DETECT AND MITIGATE INTERFERENCE

6.2.1 Narrowband interference mitigation

Conﬁguring the notch ﬁlters

When the notch

ﬁ

lters are set to their default auto mode, the receiver performs automatic

interference mitigation of the region of the spectrum aﬀected by interference. In manual
mode, as shown con

ﬁ

gured for Notch1 in Figure 6-3, the region of the aﬀected spectrum is

speci

ﬁ

ed by a center frequency and a bandwidth which is eﬀectively blanked by the notch

ﬁ

lter.

Figure 6-3:

Con

ﬁ

guring the

ﬁ

rst notch

ﬁ

lter Notch1 at 1235 MHz

With the Notch1 settings as shown in Figure 6-3, the L2-band after the notch

ﬁ

lter (After IM)

is shown in Figure 6-4 with the blanked section clearly visible.

Figure 6-4:

The RF spectrum of the L2 Band after applying the notch

ﬁ

lter at

1235 MHz

Summary of Contents for AsteRx-U3




















































































Search results

Summary of Contents for AsteRx-U3

Reviews:

Related manuals for AsteRx-U3

Brands by name

Popular brands

SEPTENTRIO AsteRx-U3, User Manual

Search results

Summary of Contents for AsteRx-U3

Reviews:

Related manuals for AsteRx-U3

Brands by name

Popular brands