background image

www.sentera.eu

MIW-ECH-8-DM-EN-000 - 22 / 08 / 2022

10 - 10

back to the table of contents

ECH-8-DM

CONTROLLER FOR WATER 
HEATERS / COOLERS WITH EC FAN

 

ATTENTION

Applying overvoltage to any of the logical controller parts will cause improper 
operation or failure to the internal circuit. 

ATTENTION

Disconnect and confirm that there is no live current flowing to the unit before servicing.

 

ATTENTION

Avoid exposing the controller to direct sunlight!

TRANSPORT AND STORAGE 

Avoid shocks and extreme conditions; stock in original packing.

WARRANTY AND RESTRICTIONS

Two years from the delivery date against defects in manufacturing. Any modifications 
or alterations to the product after the date of publication relieve the manufacturer 
of any responsibilities. The manufacturer bears no responsibility for any misprints or 
mistakes in this data.

MAINTENANCE 

In normal conditions this product is maintenance-free. If soiled, clean with a dry or 
damp cloth. In case of heavy pollution, clean with a non-aggressive product. In these 
circumstances the unit should be disconnected from the supply. Pay attention that 
no fluids enter the unit. Only reconnect it to the supply when it is completely dry.

Summary of Contents for ECH-8-DM











Reviews: