background image

sensotran, s.l. 

GAS SENSORS AND TRANSDUCERS 

ALARM PANEL 

GASVISOR 

Rev. GV v1.1 

User Manual 

Page 9 of 11 

 

 

Note: 

When  a  parameter  is  modified,  an  icon  appears  to  save  the  changes 

with a floppy disk symbol. 

 

 

4.4 RS-485 bus operation 

 

Up to 32 detectors can be connected over RS-485 bus. 

A different ID must be assigned to each detector first. 

 

 

 

 

 

 

 
 

 

 

 

 

 

 

 

 

 

An  external  power  supply  must  be  provided  to  connect  the  detectors  on  an 

RS-485 bus. 

Wiring must be by means of a 4-wire cable with 2 wires for power supply and 
2 for the communications bus (A and B). 

 

 

4.5 General alarm operation 
 

The GasVisor panel has 4 relays to activate 4 different alarms. The first three 

are used as normal alarms and the fourth a fault alarm. 

If  the  alarm  is  activated  for  any  channel,  it  will  be  displayed  in  a  different 
colour, depending on the alarm tripped, and a bell symbol will appear in the 

box  corresponding  to  the  channel.  The  value  reading  will  continue  to  be 

displayed.  
 

Oxygen sensor alarms must be configured as descending for sub-oxygenation 

levels  (below  20.9%)  and  ascending  for  over-oxygenation  levels  (above 
20.9%). 

 

If  connection  to  the  sensor  is  lost  for  any  reason,  the  fault  alarm  will  be 
activated and the text “FA” will be displayed. If this happens, the alarms on 

Bus 1 

Bus 2 

Bus 3 

Bus 4 

Summary of Contents for GasVisor












Reviews: