manualshive.com logo in svg

Sensors TOC-625, Installation And Operation Manual

Share
Download
Sensors TOC-625 Installation And Operation Manual Download Page 3

EC Declaration of Conformity

Issuers name and address:

Oliver IGD Limited of
4a Pepper Rd
Stockport, SK7 5BW
United Kingdom

Declares that the product listed as:

TOC-625 

Single or Multi-Channel Detector Control Panel

Issued on:                         At Oliver IGD Limited, Stockport, SK7 5BW , United Kingdom                                             

Notified Body For ATEX 
and/or QAN:

Sira Test & Certification Ltd
Hazardous Area Centre, 
Rake Lane
Eccleston, 
Chester, 
CH4 9JN.
United Kingdom

Oliver IGD Limited operate an 
independently assessed ISO9001:2008 
Quality Assurance System and ATEX QAN. 

Quality Assurance Certificate Number

023827

Quality Assurance Notification Number

SIRA 02ATEX M174

Signature:                                                                         

Name                                                                              Andrew J Collier  M.I.O.D

Position:                Managing Director                            Date:     5.October 2011                          Declaration Ref: TOC-625-DEC-1  
                                                                                      

Declaration of Conformity in accordance with EN ISO/IEC 17050-1:2004

Testing Agency:

CASS Industries Limited
Blackbrook Trading Estate
Weybrook Rd
Levenshulme
Manchester
M19 2QD

Are in conformity with the provisions of the following European Directive(s) when installed, operated, serviced and maintained 
in accordance with the installation and operating instructions contained in the product documentation.

And that the standards and/or technical specifications referenced below have been applied or considered.

2004/108/EC          EMC Directive     
2006/95/EC            Low Voltage Equipment Directive 

 (note not applicable to 24V DC Powered Versions)

               

EN 61779-1:2000

EN 50271:2001

Technical File Reference

Electrical apparatus for the detection and measurement of flammable gases, general 
requirements and test methods.

Electrical apparatus for the detection and measurement of combustible gases, toxic gases or 
Oxygen: requirements and tests for apparatus using software and or digital technologies. 

Excluding requirements for SIL

T625-TF9

CO

H

2

S

CO

2

SO2

NO

NO

2

CH4

SYSTEM CONTROLLER

www.sensors.ltd.uk

A Division of  International Gas Detectors

Tel: +44 (0)161 483 1415

Fax: +44 (0) 161 484 2345

Email: [email protected]

Page 3 of 25

www.sensors.ltd.uk

A Division of  International Gas Detectors

Tel: +44 (0)161 483 1415

Fax: +44 (0) 161 484 2345

Email: [email protected]

Summary of Contents for TOC-625


































Reviews:

No comments

Brands by name

Popular brands

Load more brands