background image

SPECIFICATIONS

Kit Number

6-920-3

Type

Recording Ammeter Kit, Three Phase

3 Amcorders

1 IrDA USB Cable

1 Softlink Software

1 Universal Hot Stick Adapter

1 Soft Carrying Case

Range of Operation

 Voltage

69 

kV

 

Current

1 to 1000 A

Resolution

 

Amps 1.0 to 99.9 A

0.1 A

 

Amps 100 to 1000 A

1 A

Accuracy

 

Amps

±1%, ± 2 Counts

Frequency

 

50 Hz

47 to 53 Hz

 

60 Hz

57 to 63 Hz

Mechanical

 

Weight

1.5 lbs, 0.68kg

 

Sensor Opening

up to 1.3 in, up to 3.3 cm

 

Dimensions

9.8 in x 4.8 in x 3 in (24.77 cm x 12.07 cm x 7.62 cm)

 

Housing

Shock and water resistant molded urethane

 

Operating Temperature

-22 to +140˚ F, -30 to +60˚ C

Lithium battery required for temperatures below -4°F (-20°C).

 

Storage Temperature

-40 to +158˚ F, -40 to +70˚ C

 

Hotstick Mounting

Shotgun or Universal Style Hot Stick (Hot Sticks not included)

 

Battery

9 Volt Alkaline or Lithium

Indoor/Outdoor Use

 

Relative Humidity

90% Non - Condensing

 

Altitude

9800 ft, 3000 meters

Software Requirements

Softlink by SensorLink, included in sales kit

Operating System

Windows 7, 8, or 10

Data Collection Space

64,000 Data points

EEC Standards

Successfully passed international test standards indicated by CE

Page 4

Summary of Contents for 920 FRG





















Reviews: